Hello Desk Sign
Created 1 months ago
Description
A freestanding desk sign featuring the word HELLO in an upright, bold typeface. The lettering is extruded to a 5mm thickness and sits partially embedded into a solid chamfered base plate for stability.
- Base dimensions: 110mm wide, 30mm deep, and 5mm thick
- Text thickness: 5mm, facing forward
- Chamfered top and bottom edges on the base plate
Images
More like this
Explore more in Decor & Display →
Black and Gold Wedge Desk Nameplate
A wide desk nameplate with a black rounded base, thin gold border and raised gold lettering. The name sits on the top line in large capitals, with ASSISTANT PROFESSOR centred below it in smaller capitals. The plate is tilted back on an integrated wedge stand, so it needs no separate parts. The back and underside are flat, and the build needs no supports. Text: SIMRANJEET KAUR LOHAT (top), ASSISTANT PROFESSOR (bottom) Colours: black base and wedge, gold border and letters Letters raised 2 mm, border raised 1.2 mm Plate size 200 × 64 mm, tilted back 15° from vertical Suited to multicolour printing with a 0.4 mm nozzle
Ripple Dune Twist-Lock Lamp
A soft, dune-rippled shade sits on a rounded pedestal base, like a small sand-sculpture lamp. The two pieces lock together with a printed twist-lock joint, so no hardware is needed. A bulb holder pocket sits inside the shade, and the cable runs through the base. Design notes Three lugs on the base neck drop into slots in the shade, then a short twist locks them. The cable hole enters the rear of the base and rises through the neck into the bulb pocket. The 24 mm pocket suits a small E14-style lamp holder. Use a low-heat LED bulb. Prints as two parts, base flat on the bed and shade open end down.
3-Inch "Glad to Be of Service" Door Plaque
A 76 × 76.2 mm (3 in) square plaque carrying "GLAD TO BE OF SERVICE" in raised lettering, styled after the cheerful talking doors of The Hitchhiker's Guide to the Galaxy. Layout GLAD and SERVICE are set large for emphasis; TO BE OF sits small between them. Retro sci-fi lettering, a raised border and a small smiley under the text. Backing plate is 2 mm thick; lettering and border rise 1.6 mm above it. Check before printing Overall height is 76.2 mm. Scale the whole plate if you need a different size. The smallest line, TO BE OF, is 7 mm tall, so use a 0.4 mm nozzle or finer. There are no mounting holes or stand.
Christmas Tree Lantern for LED Tealight
A Christmas tree lantern that sits over a battery LED tealight, so the light stays hidden inside instead of glaring from a bare tealight on the table. The walls are perforated with rings of small round holes that throw dots of light, and the bottom is open so the LED can be placed or swapped without taking anything apart. Key numbers Height: about 135 mm including star Base diameter: 90 mm, open underneath (inner opening about 87 mm) Wall: 1.6 mm, three stacked tiers Perforations: 4.2 mm holes, staggered rings Star: separate colour, peg-mounted into the top tier Printing Print upright, open end down, no supports needed for the cone walls Green for the tree, gold or yellow for the star Use a 0.4 mm nozzle; a lighter or translucent filament glows more
Moldura A4 Vertical 250 × 337 mm, Fundo Aberto
Moldura para folha A4 (210 × 297 mm) na vertical, em duas metades unidas por pinos-guia, com a folha entrando por uma fresta na travessa superior. Medidas Externo: 250 × 337 × 15 mm Abertura visível: 202 × 289 mm, lábio frontal de 5 mm Bolso do papel: 212 × 299 mm Fresta superior: 206 mm de largura Fixação e encaixes 4 pinos-guia de Ø5 × 8 mm na metade superior, com alojamentos de Ø5,6 mm na inferior Keyhole para prego: entrada de Ø10 mm e fenda de 4,2 mm, na travessa traseira superior Gancho na borda inferior frontal Verifique antes de imprimir Cada metade mede 250 mm de largura, acima dos 220 mm de uma impressora comum. A traseira é aberta abaixo da travessa do keyhole, então nada segura a folha por trás. Não serve para papel muito fino ou ondulado.
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.