HexGrip — Square-Cut Plywood Hex Clips
Created today
Description
HexGrip is a two-clip press-fit system for building hexagonal shelving from 1/2 in plywood, now designed for plain 90° square-cut panel ends. Each slot ends in a solid stop 5 mm from the vertex centre, so neighbouring panels meet at 120° without colliding and no mitre cuts are needed.
Features
- End Cap Clip: two slots at 120° for outer hexagon corners.
- Spoke Clip: three slots 120° apart for shared vertices in a hexagon network.
- Barbed slot walls with about 0.55 mm interference per side: ramped entry, steep faces that resist pull-out.
Dimensions
- Slot width 13.0 mm, depth 19 mm
- Clip height 24 mm, arm length 30 mm
Print notes
- Prints with the slot opening facing up, no supports needed.
- A single hexagon uses 12 clips, one on the front and one on the back of each vertex.
- Print one first to check the fit against your actual plywood thickness.
Images
More like this
Explore more in Home & Fixtures →
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
120mm Wavy Suspended Planter Pot
A contemporary, self-supporting planter insert designed to seat perfectly into a matching 130mm water reservoir. The exterior features a 12-point wave pattern with a gentle 45-degree sweeping twist, merging seamlessly into a robust 120mm upper resting lip. The interior taper mirrors the outer walls to maintain a reliable 2.5mm thickness, finishing with an elegant inner flare at the rim. Specifications Dimensions: 140mm height, 120mm max outer diameter (at the rim). Clearance: Tapered base drops to ~107mm diameter to comfortably clear standard 130mm reservoir walls. Drainage: Seven 5.5mm functional ports arranged flush to the floor. Printability: The support lip is carried by a calculated 45-degree transition collar, ensuring the overhang prints completely clean without supports. Drops right onto the build plate.
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
Twisted Planter With Name Plaque
A 100mm base hexagonal planter with a deep twist and a prominent front plaque. The planter features a solid 5mm-thick wall that precisely tracks the exterior twist, terminating in a flared rim. It includes a central 8mm drainage hole alongside five 10mm perimeter holes. A pill-shaped plaque sits seamlessly flush on the front face, equipped with extruded placeholder text ("NAME") that will export as part of the geometry—ideal for setting up multicolour text in your slicer. Check your drip tray to ensure the 100mm base clears the lip.