High Roller — Casino Poker Chips
Created 3 months ago
Remixed once
Description
Classic casino-style poker chips ready for game night. Designed at regulation size (39mm diameter, 3.3mm thickness) but tailored for easy single-color printing, featuring embossed values that pop nicely, indented edge spots, and an accent rim. Each chip value is kept as a separate component for straightforward batch printing in their traditional colors.
Features
- Regulation Sized: 39mm × 3.3mm standard dimensions.
- Double-Sided Embossing: Bold denomination values raised by 0.3mm to ensure they stand out without surpassing the protective rim.
- Casino Rim Details: Realistic edge notches and accent rings to capture the feel of standard clay chips.
- Flat Printing: Completely flat resting surface for effortless adhesion without supports.
Print notes
- No supports needed.
- Print with 100% infill to give them a heavier, more authentic feel in the hand.
- A subtle color swap or painting the raised center text will make the values instantly readable across the table.
Photos
Technical views
More like this
Explore more in Gifts, Seasonal & Personalized →
Magic octagon coin.
An octagon coin whose raised arrow disappears into the bed side: the underside is now flat with the arrow cut in as a shallow dent, so no layer prints over empty air. Size: 50 mm across corners, 3 mm body, 4.2 mm total height. Top: 0.6 mm raised rim, with the arrow rising 1.2 mm so it stands 0.6 mm above the rim. Change filament at that layer to colour only the arrow. Underside: flat, with a 0.6 mm deep arrow indentation turned 90° from the top arrow, plus a 1.4 mm wide, 0.6 mm deep groove about 2 mm in from the edge. Print: lie it flat, underside on the bed, no supports.
Raised-Text Visitor Pass 110x70 mm
A 110 × 70 mm single-piece visitor pass for Himalaya Public Sr. Sec. School, with a 2 mm base plate and bold text raised 0.8 mm above it. The three centred lines read HIMALAYA PUBLIC, SR. SEC. SCHOOL and VISITOR PASS. Plate: 110 × 70 mm, 2 mm thick, rounded corners, flat bottom Text: 0.8 mm raised, fused to the plate Total thickness: 2.8 mm Single colour, no supports needed Text size unchanged from the previous version
Ø20 mm Marker mit Zier-Fragezeichen
Runder Spielmarker, Ø20 mm und 3 mm hoch, mit einem verzierten Fragezeichen auf dem Sockel. Er passt als Hinweis- oder Rätselmarker auf Spielfelder. Maße und Aufbau Sockel: Ø20 mm, 2 mm dick, obere Kante mit 0,3 mm Fase Fragezeichen: 1 mm erhaben, Gesamthöhe 3 mm, ca. 14 mm hoch Details: Endknopf am Bogen, Zierperle im Schaft, Punkt mit zwei Zierspitzen Zierrand: schmaler Ring mit zwölf Perlen, 0,6 mm erhaben Vor dem Druck prüfen Der Zierring liegt bei Ø18 mm. Wenn der Spielfeldrand oder eine Halterung enger ist, vorher messen. Passt nicht Kein Ersatz für Marker mit anderem Durchmesser als 20 mm.
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
Armoured Oyster Bracelet Mid-Link
A reinforced stand-in for a broken oyster-style solid link, with a crowned top and an R45 concave underside that follows the wrist. The hinge ends are built to take the load. Female end: two Ø5.2 ears around a 5.2 mm gap; male end: one Ø4.6 × 4.4 mm tongue. Ø1.6 pin bores, 35.8 mm pin to pin. Underside pocket stops 11 mm from centre, leaving solid hinge zones. Filleted webs where the ears meet the body. Ream the pin holes to 1.5 mm after printing.
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.