Kawasaki M12x1.25 Skirted Mirror Cap
Created 1 months ago
Description
Threaded blanking cap for M12x1.25 motorcycle mirror mounts, designed to seal the exposed mounting boss after switching to bar-end mirrors. The flat, beveled head deflects weather, while the outer lip drops down over the factory hardware to stop water getting underneath.
Fitment and Specifications
- Thread Standard: M12x1.25 fine pitch.
- Critical Check: Verify the factory bore diameter on the motorcycle. While this model is cut for M12, a significant number of Kawasaki factory mounts use M10 threads.
- Clearance: The 3mm deep weather skirt has an 18.5mm internal diameter, providing 0.25mm of radial clearance over a standard 18mm factory boss.
- Known Incompatibilities: Yamaha and certain right-hand Kawasaki mounts use a reverse (left-hand) thread. If the printed cap refuses to thread into the right side, mirror the geometry in the slicer or remix to reverse the thread direction.
Images
More like this
Explore more in Automotive, RC & Hobby →
Double Seatbelt Buckle Holder, Backseat
Two seatbelt buckles flop around and fall into the seat gap, so this holder stands both upright side by side in the backseat of a Toyota Sienta. Each 33 x 53 mm pocket goes straight through the base, so the buckle and webbing pass through with nothing blocking the bottom. Pocket size: 33 x 53 mm each, sized for a 31 x 51 mm buckle Sleeve height: 28 mm above a 6 mm base Overall footprint: 130 x 64 mm Centre screw hole: 4.5 mm Print flat on the base, no supports needed
Line Follower Chassis (N20/Mega)
A flat-printing, modular chassis designed specifically for high-speed line following. Engineered to accommodate an Arduino Mega 2560, dual N20 motors, and a Pololu QTR-8RC reflectance sensor, with priority placed on a low center of gravity and straightforward field maintenance. What it's for This frame carries the electronics and drive system for a 2WD differential steering robot. Components drop into dedicated regions rather than requiring complex brackets, and all sensitive electronics are kept clear of the track surface. The front sensor mount separates from the main plate to allow independent height tuning of the IR array. Dimensions Overall envelope (assembled): 180 mm (L) × 130 mm (W) × 55 mm (H) Track width: ~90 mm, providing clearance for 35–38 mm diameter wheels. Electronics rails: Slotted cross-members accept an Arduino Mega or similarly sized microcontrollers. Drive mounts: Drop-in snap/strap cradles for standard 12×10 mm N20 motors. Power bay: Sized for two parallel 18650 lithium cells (44 mm inner width) with integrated Velcro pass-throughs. Assembly All major features anchor with standard M2 or M3 hardware. The front skid and sensor bracket print flat independently and bolt into designated sliding rails on the chassis nose. The motor mounts include under-plate zip-tie channels to secure the gearboxes rigidly against torque. Use standoffs for the motor driver and buck converter pads to ensure proper wiring clearance above the deck.
Freelance Lego fitting cab with Headlight Studs
Brute is a hollow, LEGO-compatible cab modelled loosely on the British Class 47 locomotive. It is six studs wide and four deep, with a closed floor that carries a grid of sockets so it presses onto a standard baseplate. Two studs on the nose give a place to clip on headlight pieces. Features Raked twin windscreens and side door windows Flat, smooth roof at five-brick height Two studs on the front face for headlights Lamp recess centred between the headlight studs 6×4 socket grid under the floor Dimensions Width: 47.8 mm Depth: 31.8 mm Height: 48 mm to the roof Headlight studs: 4.8 mm diameter, 8 mm either side of centre Print notes Print upright on the floor plate, or flipped onto the roof for a clean top surface. Hollow underneath and open at the rear.
Vented 50mm Speaker Basket
A custom 3D-printable 50mm speaker basket designed for custom driver assemblies. It provides a rigid framework linking a standard 50mm top surround ring to a tailored bottom magnet housing. This version features a completely hollow core: Pass-Through Bottom: The central pole has been deleted and the floor bored out to 25mm, allowing full clearance for a voice coil and T-yoke assembly. Magnet Seat: Leaves a 3mm resting lip for a standard 31mm ring magnet. Acoustic Venting: Four structural struts anchor the assembly while maximizing rear airflow.
Vented Acoustic Basket
A skeletal mounting chassis designed to hold a custom 50mm driver assembly. The aggressive cutouts strip away unnecessary mass, leaving four sweeping struts that provide rigid support while entirely opening the rear wave to prevent acoustic reflections. The base houses a precision-cut cavity tailored to scavenged PC fan magnets, complete with a vented central pole piece. Acoustic Details Rear Ventilation: 50-degree windows cut low into the voice coil gap ensure maximum airflow and heat dissipation. Magnet Housing: A 28.5mm OD x 5mm bottom slot sized specifically for standard 120mm fan ring magnets. Mounting Interface: 50mm outer diameter upper ring with a 2mm wall thickness for standard cone attachment.
RC Car Bevel Gear Rear Drive
A rear-axle drive for an RC car where the motor shaft has to turn 90° into a cross-car axle without the gears skipping or the motor shifting. This set uses a 12-tooth pinion and 24-tooth crown gear (2:1) on a 103.9 mm × 6 mm axle, with an open motor cradle instead of a closed box. Key numbers Gears: module 1.5, 20° pressure angle, 4 mm face width, 90° shaft angle Pitch cone angles: 26.57° (pinion) and 63.43° (crown); cone distance about 20.1 mm Pinion bore 2.1 mm, crown bore 6.2 mm, both with M3 set-screw holes in the hubs Axle supports: 6.4 mm through-hole plus a 17.3 mm seat for 606 bearings (6×17×6) Base: 84 × 92 × 5 mm, M3 holes (3.4 mm clearance); cradle slots allow forward and back adjustment Motor cradle parameters at the top of the file: mw, mh, wall, saddlel, saddley. Measure the real motor and edit them Cover is open at the bottom, with two M3 ears at the rear Printing Print gears with the hub facing up or down on the bed; PETG or nylon preferred Cover prints open-side up without supports Axle is a separate 6 mm steel rod; M3 screws hold supports, cradle, straps and cover