Lifebuoy — Wall Key Rack
Created today
Description
Lifebuoy is a wall-mounted key rack shaped like a beach lifeguard buoy, with a red body, white LIFEGUARD lettering and five sturdy hooks.
Features
- 230 mm long stadium-shaped body, 70 mm tall, 14 mm deep
- Letters as a separate white piece set into a pocket in the red body
- Five round-tipped hooks along the lower front
- Two rear keyhole-style screw holes with counterbores
- Flat back for printing without supports
Print notes
Print the body and the letters in separate colours (PLA, 0.4 mm nozzle), back face down.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Under-Sink Bag Roll Dispenser Barrel
A grocery-store bag-roll dispenser, shrunk down and bolted under the sink. A snug barrel holds a 60 mm roll of trash bags, and the next bag's edge hangs out of a slot in the bottom, ready to grab. A serrated lip along the front of the slot tears each bag off cleanly, so there's no more digging for the end of the roll. The barrel is closed at one end and open at the other. A separate press-fit end cap seals the open end once the roll is loaded. Design notes Bore: 64 mm diameter for a 60 mm roll, with 3 mm walls. Length: 130 mm overall. Dispensing slot: 20 mm wide, running along the bottom of the barrel. Tear lip: a row of downward-pointing teeth at 4 mm pitch on the front edge of the slot. Mounting: a flat back plate with two countersunk screw holes. The holes sit above the barrel, so screws never cross the bore. End cap: printed as its own piece, with a plug that fits the bore and a flange that matches the barrel. Print and remix notes The teeth are the lowest points as modelled, so plan on supports under the barrel. Printing the part on its back plate is an easy re-orientation. Slot length, tooth pitch and screw spacing are the obvious values to adjust for other roll sizes or cabinet layouts.
Wide Hook With Tall Front Lip
A small wall-side hook, 20 mm wide and 15 mm deep, with a 20 mm back plate, a flat 3 mm arm and a 50 mm upturned front lip. Remix hooks Width (20 mm): the one value shared by the plate, arm and lip. Widen it for heavier loads or narrow it for tight spots. Lip height (50 mm): lower it to around 10–15 mm for a simple catch, or keep it tall to hold flat items upright. Back plate height (20 mm): raise it to leave room for a screw hole or two. Arm thickness (3 mm): thicken it if the hook will carry weight. Pairs well with countersunk screw holes in the back plate or double-sided mounting tape.
110x80mm Invertible Wall Shelf
A simple, sturdy wall shelf with a subtle rim on the underside, designed so it can be mounted inverted. Features a 110x80mm flat area and integrated reinforcement gussets for rigidity against the wall. Dimensions: 110mm width x 80mm depth. Mounting: Twin countersunk screw holes on the backplate. Features: 3mm retention lip and dual structural gussets.
Appendiabiti a Traliccio 32mm
Appendiabiti rigido a parete stampabile in 3D. Disegnato con un profilo sagomato per ridurre il consumo di filamento mantenendo un'elevata resistenza al carico. Interasse: 32 mm esatti. Fori: 3,2 mm (per viti da 3 mm), con svasature da 4,5 mm posizionate a profondità fissa. Accessibilità: tunnel orizzontali da 8,5 mm per inserire agilmente vite e cacciavite. Orientamento: Da stampare rigorosamente coricato sul fianco per sfruttare la direzione dei layer.
Flat-Backed Angled Wall Hook
A 3D-printable wall hook featuring a straight outer spine for a clean visual line against the wall, paired with a curved inner profile that creates a natural resting notch. Straight spine: Sits perfectly parallel to the mounting plate. Inward curve: Adds depth to the hook's catch without thinning the whole shaft. Base plate: 30x30 mm, sized for standard mounting tape.