Made by KriticalHitical
Created 3 days ago
Description
Three-piece henna cone stand: a 4 × 4 inch (101.6 mm) upper plate, a 6 × 6 inch (152.4 mm) base and a 127 mm center rod, joined by M16 × 3 mm threads.
Print the small thread test nut first and confirm it turns on the rod's M16 × 3 mm thread.
Images

Open-top storage box with three equal compartments side by side, and the name CHARO raised across the full front face. Outer size: 210 x 112 x 85 mm Walls and dividers: 3 mm Floor: 4 mm Compartments: 3, each about 66 x 106 mm inside Lettering: Bebas Neue, about 200 x 77 mm, raised 1 mm on the front Prints upright with no supports
这是一套需要组装的、可多层叠加的茶包抽屉,按 PLA 打印设计:底座框架内装两组定滑轨与动滑轨,抽屉盒体沿轨抽出,前端用两颗 D4×2 磁铁吸合,四角堆叠卡扣让相同单元上下定位。打印件包括底座、抽屉盒体、动/定滑轨各 2 件、4 个堆叠卡扣和抽屉端板;组装用 M3×8 平头螺栓。 可改的起始尺寸 底座框架:140×110×32 mm,后部开窗;侧壁 3 mm。 抽屉盒体:外尺寸 126×98×26 mm;前壁 2 个 Φ4 磁铁沉孔,设计深 2.2 mm。 滑轨:定/动滑轨各 2 件,长 110 mm;动定之间留 0.2 mm 滑动间隙。滑轨为 2 mm 薄片,受底座侧壁厚度限制。 堆叠卡扣:42×18×14 mm,四角各一件;抽屉端板:106×28×6 mm。 紧固孔:M3 沉头过孔 Φ3.4 mm;磁铁:D4×2 mm。 换版时先动这几处 先改抽屉盒体的长宽高,底座和端板跟着放量,滑轨长度保持 110 mm 或按新行程加长。 0.2 mm 滑动间隙是抽拉手感的关键,材料收缩大时先调这里,不要先改轨形。 堆叠卡扣的 42×18×14 mm 决定层间定位;要叠更高或换更厚板材,优先改卡扣高度与卡口深度。 磁铁沉孔按 Φ4×2.2 mm 设计;想换 D5 或 D6 磁铁,直接放大沉孔与对应磁铁位。 M3 沉头孔为 Φ3.4 mm 过孔,螺栓头不会完全埋平;需要齐平就加深或扩大沉孔。 如果要继续做系列,这套盒体适合与同尺寸底座、不同深度的抽屉盒,以及带标签孔的端板配对;保持四角卡扣和滑轨接口不变,就能混搭层数。
PivotTee è un portabrugole piatto per chiavi a T da 10 a 3 mm, con perni laterali che lo fanno ruotare da orizzontale a verticale su una base da fissare al cassetto. Un fermo girevole dietro il blocco lo tiene in verticale durante l'uso, e il perno centrale accoglie un inserto filettato M3 per avvitare il fermo. Caratteristiche Otto sedi da 10 a 3 mm con fessura superiore e numeri incisi Base con due fori svasati da 5 mm Perno del fermo da 8 mm con foro da 4,2 mm per inserto M3 (profondità circa 8 mm) Fermo girevole 44 × 14 × 6 mm Print notes Tre pezzi stampati sdraiati, senza supporti Inserto filettato da scaldare a caldo nel foro del perno
A three-tier slatted shoe rack, 500 × 300 × 480 mm, holding six pairs (two per shelf), now with decorative trim. Remix hooks Side diamonds: 22 mm diamond cutouts on each side panel, two per tier. Change the size, count or shape (hexagon, circle) to taste. Scalloped crown: 30 mm half-round bumps along the top of the back panel, spaced 50 mm. Widen the spacing for a calmer look. Corner finials: 18 mm spheres on the four top corners. Swap for cones or pyramids. Pairs with: splitting into panels for printing; the 8 mm wall suits dowel or screw joints. Dimensions to keep: shelf spacing (40/190/340 mm) sets shoe clearance.
Loose items slide around in a drawer, and a floorless box with a divider keeps them in place. This one is a rectangular frame with no floor and a full-height wall across the middle. Key numbers Outer size: 184 x 93.33 x 115 mm (height) Wall thickness: 2.4 mm Divider: 2.4 mm, full height, at the middle of the 184 mm length Three boxes side by side fill a 280 mm drawer depth Print: open end up, no supports needed, fits beds of 210 mm or larger

Gavetas e bancadas viram bagunça quando parafusos, cabos e peças pequenas se misturam. Esta caixa organizadora separa tudo em 6 compartimentos fixos, em grade de 3 x 2. Medidas e impressão Tamanho externo: 180 x 120 x 50 mm Paredes e fundo: 2 mm Divisórias: 2 mm, 5 mm mais baixas que a borda Cada compartimento mede cerca de 56 x 57 mm por dentro Imprime sem suportes, com o fundo apoiado na mesa PLA ou PETG, com 0,2 mm de altura de camada