Magic octagon coin.
Created today
Description
An octagon coin whose raised arrow disappears into the bed side: the underside is now flat with the arrow cut in as a shallow dent, so no layer prints over empty air.
- Size: 50 mm across corners, 3 mm body, 4.2 mm total height.
- Top: 0.6 mm raised rim, with the arrow rising 1.2 mm so it stands 0.6 mm above the rim. Change filament at that layer to colour only the arrow.
- Underside: flat, with a 0.6 mm deep arrow indentation turned 90° from the top arrow, plus a 1.4 mm wide, 0.6 mm deep groove about 2 mm in from the edge.
- Print: lie it flat, underside on the bed, no supports.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.
Luggage Strap Tag, 5 mm Slot, STEVE
A 90 × 50 × 3 mm luggage tag with a 5 × 22 mm strap slot and the name STEVE raised inside a recessed label panel. Fitment Fits straps up to 5 mm thick through the 22 mm-wide slot. Does not fit wide or double-layer straps, or standard key rings without a loop. Measure the strap thickness before printing; the slot is 5 mm. The lettering stands 0.9 mm proud of the panel floor and sits below the tag's top surface, so it is protected from rubbing.
Raised-Text Visitor Pass 110x70 mm
A 110 × 70 mm single-piece visitor pass for Himalaya Public Sr. Sec. School, with a 2 mm base plate and bold text raised 0.8 mm above it. The three centred lines read HIMALAYA PUBLIC, SR. SEC. SCHOOL and VISITOR PASS. Plate: 110 × 70 mm, 2 mm thick, rounded corners, flat bottom Text: 0.8 mm raised, fused to the plate Total thickness: 2.8 mm Single colour, no supports needed Text size unchanged from the previous version
Single-Colour Raised Text Visitor Pass
A 110 × 70 mm visitor pass with a 1.2 mm plate and bold raised lettering standing 0.6 mm proud, 1.8 mm total. It prints flat-side down in one colour with no supports. Remix hooks Text sizes: 6.5 mm for the school lines and 7.5 mm for VISITOR PASS. Raise them for a bolder look, but keep 4 mm of edge clearance. Plate thickness: 1.2 mm. Thicker gives a stiffer card, though the total height rises with it. Relief height: 0.6 mm. Match it to your layer height, for example 3 layers at 0.2 mm. Pairs with: a lanyard slot or clip tab added at one end.
Ø20 mm Marker mit Zier-Fragezeichen
Runder Spielmarker, Ø20 mm und 3 mm hoch, mit einem verzierten Fragezeichen auf dem Sockel. Er passt als Hinweis- oder Rätselmarker auf Spielfelder. Maße und Aufbau Sockel: Ø20 mm, 2 mm dick, obere Kante mit 0,3 mm Fase Fragezeichen: 1 mm erhaben, Gesamthöhe 3 mm, ca. 14 mm hoch Details: Endknopf am Bogen, Zierperle im Schaft, Punkt mit zwei Zierspitzen Zierrand: schmaler Ring mit zwölf Perlen, 0,6 mm erhaben Vor dem Druck prüfen Der Zierring liegt bei Ø18 mm. Wenn der Spielfeldrand oder eine Halterung enger ist, vorher messen. Passt nicht Kein Ersatz für Marker mit anderem Durchmesser als 20 mm.
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament