MagSafe iPhone Desk Stand (fixed)
Created 1 months ago
Description
This MagSafe desk stand ends the daily annoyance of a phone lying flat on a desk catching glare and demanding two hands to peel away from a charging cord. It angles the screen at 60 degrees for casual checking, leaves plenty of airgap for the heavy camera bumps on modern iPhones, and traps the charging cable permanently in place so it stops sliding off the table.
Tolerances and Fit
- Puck Recess: 56.5mm diameter by 5.7mm deep — dimensioned to grip a bare official Apple MagSafe charger securely.
- Cable Channel: A 7.5mm wide routed track runs straight down the front face of the arm and channels the cord cleanly under the heavy base plate.
- Ejection Hole: A 25mm rear bore gives your thumb space to push the charger out when you need to pack it for a trip.
Images
More like this
Explore more in Desk & Tech →
19.5mm Desk Edge Puck Mount
Edge-mounted charging cradle sized for the 33.5mm Google Pixel Watch magnetic puck. Designed to drop over a standard 3/4-inch (19.5mm) wood plank. Fitment: The 33.5mm bore sits at the rear of the housing. You push the puck in from the back, then slide the whole assembly over your desk edge — the wood itself traps the puck so it cannot back out. Cable Routing: An 8mm slot on the bottom allows the cable to drop cleanly out of the way. Incompatibilities: Does not fit full-sized phone Qi chargers or desks thicker than 19.5mm without adjustment. Phone hooks have been removed from this version.
Modular Hexagonal Phone Stand
What it's for A single-piece modular phone stand designed around a regular hexagonal footprint. It features an angled 70-degree backrest for optimal viewing and a sturdy front retaining lip. A central U-groove is carved through the front lip and into the base, allowing a charging cable to pass cleanly underneath the phone while docked. The stand is designed to tile: dovetail tabs on the right side match with identical slots on the left side, allowing multiple hexagonal units to be linked together into a continuous charging array or desk organizer without any extra hardware. Dimensions Base size: 80 mm across opposite vertices, sitting 6 mm thick. Back panel: 65 mm tall, leaning back at a 20-degree angle from vertical. Front lip: 10 mm high above the resting surface, leaving a generous 23 mm gap for the device. Cable groove: 12 mm wide, recessing down to a 2 mm floor height. Print notes Designed to print entirely support-free in its default upright orientation. The 0.2 mm clearance on the dovetail joints should slide together firmly on a well-calibrated machine. Standard PLA or PETG will provide plenty of strength for the upright panels.
Hexa — Modular Hex Phone Stand
Hexa is a one-piece phone stand built on an 80 mm hexagonal base, designed so identical modules can click together side by side with no hardware. A 70° back panel supports the phone, a front lip stops it sliding, and a groove keeps the charging cable tidy. Features Hexagon 80 mm across vertices, 6 mm thick, rounded edges Back panel about 65 mm tall, leaning at 70° from the base Front lip 10 mm above the base surface Cable groove running front to back, centred Dovetail tab on one side edge, matching slot on the opposite edge (0.3 mm clearance) Print notes Print flat on the base, no supports needed PLA or PETG, 3–4 perimeters for strength
Modular Hexagon Phone Stand
A modern, modular phone stand built around a pure hexagonal base. The design allows multiple units to link together sideways via a built-in tab and slot system, perfect for keeping a row of devices organized on a desk or creating an expanding charging station. Design Highlights: 70-Degree Rest: The back support leans back comfortably for viewing notifications or media. Cable Management: A central pass-through routes your charging cable securely out the bottom via hidden channels. Print-in-Place Linkage: Built-in puzzle-piece connections require no extra hardware to link modules. Split Front Lip: Keeps the device firmly seated while leaving the center clear for downward cable runs.
Airpods clip
A compact, single-piece dual clip designed to snap onto the stems of AirPods Pro, holding the pair securely together without the charging case. The inner bores feature flared entries at the top and bottom to guide the stems in smoothly, while the front openings are angled to flex just enough to let the earbuds snap in and out laterally. The design prints flat without supports and relies on the natural stiffness of the filament to grip the smooth plastic of the stems. Remix Hooks This geometry is essentially a tension spring—the fit relies on your printer's tolerances and the material you choose. Opening Gap (Currently 4.8 mm): If PLA snaps when inserting the earbuds, widen the inner points of the front slot. Inner Diameter (Currently 6.4 mm): Sized for a snug friction fit on the Pro stems. Dial this up slightly if using a very rigid material, or down if you want a tighter lock. Bridge Thickness (Currently 4.5 mm): Widen this if you want to attach a lanyard loop or carabiner hole to the center.
A-Frame Mobile Stand
A sturdy, functional stand for phones and small tablets. Designed with a 35-degree viewing angle, it works nicely for watching media or keeping an eye on notifications while at your desk. Features a 16mm-wide cutout for routing charging cables Includes a solid rear spine to prevent flexing when tapping the screen 14mm resting gap accommodates most phones, even with a case Prints in one piece without supports