Moldura A4 Vertical 250 × 337 mm, Fundo Aberto
Created today
Description
Moldura para folha A4 (210 × 297 mm) na vertical, em duas metades unidas por pinos-guia, com a folha entrando por uma fresta na travessa superior.
Medidas
- Externo: 250 × 337 × 15 mm
- Abertura visível: 202 × 289 mm, lábio frontal de 5 mm
- Bolso do papel: 212 × 299 mm
- Fresta superior: 206 mm de largura
Fixação e encaixes
- 4 pinos-guia de Ø5 × 8 mm na metade superior, com alojamentos de Ø5,6 mm na inferior
- Keyhole para prego: entrada de Ø10 mm e fenda de 4,2 mm, na travessa traseira superior
- Gancho na borda inferior frontal
Verifique antes de imprimir
Cada metade mede 250 mm de largura, acima dos 220 mm de uma impressora comum. A traseira é aberta abaixo da travessa do keyhole, então nada segura a folha por trás. Não serve para papel muito fino ou ondulado.
Images
More like this
Explore more in Decor & Display →
Moldura de Parede A4 com Gancho
Moldura de parede para folha A4 com gancho em J fechado na borda inferior e suporte para prego escondido no verso. A folha desliza pela abertura no topo e fica num rebaixo atrás da janela. O gancho tem a aba de retorno voltada para a moldura, formando uma abertura fechada. O suporte com furo de fechadura fica na parte de trás, no topo, e não aparece de frente. Moldura externa: 240 x 327 mm Janela: 196 x 283 mm Gancho em J: 16 mm de largura, 24 mm de altura Suporte de prego: aba traseira de 4 mm com furo de fechadura
Anel de Guardanapo com Cruz
Anel de guardanapo com cruz à frente, para o tecido não escorregar nem ficar solto na mesa. A cruz fica separada do círculo e presa por uma ponte sólida, em uma peça única. Diâmetro interno do anel: 45 mm, parede de 3 mm, altura de 5 mm Cruz: 50 mm de altura, haste de 12 mm de largura e 5 mm de espessura Ponte de ligação: 8 mm de largura, 12 mm de altura Impressão FDM em PLA; a parte de baixo do anel elevado pode pedir suporte
Watch Bracelet Mid-Link 14 x 31 mm
Replacement mid-link for a metal watch bracelet, 14 mm wide and 31 mm long, with a crowned top, a forked female hinge end and a single-tongue male hinge end. Pin holes are 1.6 mm for reaming. The underside is pocketed to save material. Body: 14.0 x 31.0 x 3.4 mm, 1.4 mm edge fillets Crown: raised 0.8 mm above the body top Female end: two 5.2 mm diameter ears, 5.2 mm slot Male end: 4.6 mm diameter tongue, 4.4 mm wide Pin holes: 1.6 mm, at Y = ±17.9 (35.8 mm pin to pin) Underside pocket: 1.9 mm deep, 0.7 mm corner radius Wrist curve not applied; exported flat Intended for PETG, printed bottom face down
Posable Dragon With Friction Joints
A posable toy dragon that holds its pose, with detailing so it doesn't look like a plain chain of balls. The old version looked like a bare stick of linked beads. This one adds belly plates, scale studs and a trimmed base. What's on it Cream belly plates under each body link Dark-red scale studs along both flanks, plus the back spike row Raised gold trim around the edge of the base Same 12 ball-jointed body links and ball-jointed head Print notes 0.2 mm joint clearance: raise it if the joints fuse, lower it if they sag Print in PETG for repeated bending Multi-colour print or paint the belly plates, trim and spikes
Mandarin Community Town Model
A tabletop town for practising Mandarin place words, where flat labels get lost. Each building, sign and park area carries its Chinese characters, pinyin and English on the front face, so the vocabulary sits right on the thing it names. Details that matter Base: 200 × 200 mm, 4 mm thick plate Buildings: hospital, library, community center, store and school, each 46 × 28 mm footprint Extras: park with pond, road, footpaths, houses, cars, trees, lamps and figures Colour regions: ground, road, walls, roofs, doors, lettering, signs, trees, lawn, pond, paths Print: large bed needed (or scale down); multicolour or paint by region; lettering is 0.8 mm raised, so use a 0.4 mm nozzle
Barbie Wardrobe With Hinged Doors
A doll-sized wardrobe, 270 × 250 × 70 mm, designed to print lying on its back. Two hinged doors close over a fully open interior with one hanging rod running wall to wall, so dresses hang on both sides. Remix hooks Rod diameter: 8 mm now. Drop to 5–6 mm for doll hangers, or go thicker if it sags over the 262 mm span. Rod height: sits 28 mm up from the back panel and 12 mm in from the rear wall. Move it to change how far dresses hang from the doors. Mid support: the span is unsupported. A thin centre bracket or a second shorter rod would stiffen it. Doors: 5 mm thick, 0.5 mm gaps, pin hinges at the outer edges. Print separately and flat. Pairs with: a printed set of doll hangers, or a shelf insert dropped into one half.