Mouse Wheel Spinner Rig
Created 1 months ago
Description
A motorized jig designed to continuously spin a computer mouse scroll wheel. Built around a NEMA 17 stepper motor and a standard GT2 280mm belt, it drives an overhead rod that rolls against the mouse.
- Adjustable Driven Shaft: The vertical towers feature 25mm of sliding travel to handle different mouse profiles.
- Bearing Housings: Included clamping blocks designed for standard 608RS bearings (with integrated crush ribs for a tight fit).
- Rod Adapters: Collar sleeves step the 8mm bearing inner diameter down to a 5mm rod.
- Motor Tensioning: The NEMA 17 faceplate has 10mm of slotted travel to easily tension the timing belt.
Images
More like this
Explore more in Workshop & Tools →
Split-Span Laser Gantry
A modular laser mounting gantry spanning an exact 330mm width. Built for smaller print beds, the two-piece frame locks together in the centre with a clearance-tuned puzzle joint that draws the span tight when seated. Adjustments & Tolerances The Joint: 0.5mm clearance around the jigsaw neck. Best printed flat to put layer strength along the span. The Slider: Sits exactly over the seam and locks down with an M4 tap bolt through the top. Laser Mount: Single 6.5mm hole on the face block, ready for standard laser unit clamps. Table Mount: Four 5.5mm mounting holes positioned straight down through the feet for screwing straight into your baseboard.
Hoof Evener Thumb Ring
A low-profile thumb ring designed to friction-fit onto the center support of a hoof-evener ruler. The ring is split to flex over a variety of thumb sizes while keeping the geometric center locked perfectly inline with the measurement zero-point. Remix Hooks Thumb clearance: Currently set to an inner diameter of 22mm. The 5mm split opening allows for expansion, but the base diameter is the first thing to dial in for a specific hand. Strut channel: The rear mounting slot is sized for a 12.5mm × 4.5mm vertical support. Adjust this block to match the actual sheet metal or printed strut of the evener. Locking hole: A 3.3mm pilot hole runs through the back wall. Drive an M4 set screw or short bolt through it if the friction fit over the strut needs extra bite.
montre
What it's for A 3D-printable watch case modelled on dive-watch proportions. Features a scalloped rotating-style bezel with minute markers, a fine threaded base for the case back, and integrated lugs for a standard watch strap. The inner cavity tapers to secure a movement, with a lip cut for a domed crystal. Dimensions Overall Case: 42 mm diameter Inner Cavity: 41 mm base, tapering to 40.4 mm at the dial Lugs: Spaced for a 20 mm strap Crystal Seat: 41.4 mm diameter, 1 mm deep Stem Hole: 1.1 mm diameter at the 3 o'clock position Threads: 0.5 mm pitch, matching case back included Print notes The case back uses a very fine 0.5 mm thread pitch. This requires a well-calibrated printer and low layer heights (0.12 mm or finer) to print cleanly. You may need to scale the case back slightly on the X and Y axes depending on your printer's tolerances.
Ojačana Vakuum Račva Sa Navojima
Ojačana račva u obliku slova T za spajanje cevi i vakumetra. Glavno telo: Prečnik 21 mm, dužina 44 mm, zatvoreno sa jedne strane. Na otvorenom kraju nalazi se integrisani ženski 1/4" BSP navoj za vakumetar, sa plitko oborenom ivicom. Krak sa navojem: Ukupna dužina 27 mm (12 mm glatki deo, 15 mm navoj na vrhu). Spoljni navoj je M12 sa korakom 1.25. Kroz njega prolazi kanal od 6.2 mm. Glatki krak: Dužina 26 mm, spoljni prečnik 10 mm. Kanal za protok je 6 mm. Ojačanja na spoju oba kraka sa glavnim telom smanjuju stres pod uglom od 90 stepeni i sprečavaju lomljenje slojeva tokom upotrebe.
GripTurn — M12x1.25 Knurled Cap
Ova zaštitna kapa donosi jednostavno, pouzdano zatvaranje za svaki M12x1.25 navoj. Dizajnirana s urezanim rebrima po cijelom vanjskom opsegu, omogućuje čvrst hvat i lagano ručno zatezanje, dok precizan profil čuva navoj od prljavštine i oštećenja. Gornja strana zatvara kapu, a mali otvor služi za provlačenje konca, sajle ili ventilaciju. Specifikacije Navoj: M12 × 1.25 (unutarnji, dubina 20 mm) Vanjske dimenzije: Promjer 20 mm, visina 22 mm Gornji otvor: Promjer 2.8 mm Površina: Rebrasta za lakše okretanje prstima
Screw-On Large-Hole Spool Holder
A plate-mounted spool holder for filament spools with large central holes. A hollow 48 mm spindle rises from a flat mounting plate and ends in a flared lip that keeps the spool from sliding off. Remix hooks Spindle diameter (48 mm): change to suit your spool bore; most big-hole spools measure 50–58 mm, so leave 2–4 mm of play. Spindle length (70 mm): stretch for wide spools, shorten for slim ones. Plate (110 × 64 × 6 mm): screw holes sit 44 mm either side of centre, 4.5 mm with countersinks. Move them to match your panel, or add a third hole. Lip: 58 mm with a 45° underside so it prints without supports. Make it a removable cap for easy spool swaps. Wall (3 mm): thicken for heavy 3 kg spools, or add ribs. Prints plate-down with the spindle pointing up. Mount with the plate against a vertical panel so the spindle points sideways; a pair stacks well for dual spools.