NDS 541 Channel Drain Grate
Created today
Description
What it's for
A heavy-duty replacement channel drain grate cover designed to closely match the NDS 541 specification. It features an inverted U-channel geometry with outward-facing bottom seating flanges, making it ideal for dropping directly into standard trench drain rails.
Dimensions
- Top Surface Width: 2.75 inches (69.85 mm)
- Total Height: 3.125 inches (79.375 mm)
- Overall Base Width: 3.5 inches (88.9 mm)
- Top Lip Thickness: 0.25 inches (6.35 mm)
- Segment Length: 200 mm
Print notes
- Modeled solid to avoid manifold errors and guarantee clean slicing.
- Includes transverse internal load-bearing ribs to prevent the tall side walls from buckling under pressure or deflecting during the print.
- Print flat on its base. No supports required. Use PETG or ASA for outdoor UV and impact resistance.
Images
More like this
Explore more in Home & Fixtures →
110mm Hex-Mesh Planter Pot
A tapered cover pot designed for standard 12cm nursery planters. The base and walls feature a staggered hexagonal mesh that promotes extensive airflow and rapid drainage. Dimensions: 150mm outer top diameter, 140mm inner top, tapering to fit a 120mm base. Total height is 120mm. Printability: The wall hexagons are rotated so their corners point straight up, yielding sharp 60-degree overhangs that print perfectly without supports. Durability: Uniform 5mm walls provide rigidity even with the extensive mesh cutouts.
Garage Vent to 6-Inch Adapter
A custom 2-part venting adapter designed to connect a 360x210mm drywall vent gap to a standard 6-inch exhaust duct. Two-Part Assembly: Splits perfectly down the middle with a 10mm external flat flange for easy gluing. Tapered Male Fitting: Connects securely inside standard 6-inch ducting. Support-Free Print: Internal lofts are designed to print cleanly with no supports while encouraging laminar exhaust flow. Mounting Integration: Six #6 screw holes for securing to drywall, with an extended bottom footing to rest cleanly on a garage concrete foundation.
bird bath shower head 5/16" 2
A friction-fit spray nozzle designed to convert a standard 5/16" ID water line into a wide, gentle shower for a bird bath or fountain. The part is modelled upside down (spray face flat on the Z-plane) so it prints cleanly as a single hollow body without any internal or external supports. Parameters to Play With If you take this into your own setup, here are the numbers driving the shape: The Stem Fit: Tapers from 8.5mm down to 7.2mm over a 20mm length. This is the sweet spot to wedge tightly into soft 5/16" (7.94mm) tubing without blowing out under mild pump pressure. The Spray Face: A 45mm outer diameter with a flat 2mm-thick face plate. The Holes: Uses a grid of 1.5mm holes spaced 3.5mm apart. Remix Hooks Flow Rate: If your pump is struggling to push water through, widen the internal 4.5mm bore or bump the face holes from 1.5mm up to 2.5mm. Directional Spray: Instead of a full grid of holes, mask off half the face to create a directional fan spray. Barbs: The smooth taper seals well for low pressure, but if you're running higher pressure, swapping the smooth cone for a stepped barbed profile will lock the tubing down harder.
Olympus — Modular Tall Planter
Olympus is a three-piece modular planter designed specifically for succulents, bonsai, and trailing vines that benefit from elevation without requiring a massive volume of soil. The fluted Greek column design prints cleanly in three support-free segments. The lower pedestal features a hollow core designed to be filled with sand or gravel for substantial bottom-weight, preventing the tall assembly from tipping. The upper capital locks onto the base and contains an internal water catch basin, while the dedicated nursery insert drops cleanly into the top with a full grid of drainage holes. Dimensions Total Assembled Height: 350 mm Maximum Diameter (Capital): 175 mm Nursery Insert Cavity: 149 mm diameter x 82 mm depth (approx. 1.4 liters) Print Notes Supports: None required. All overhangs and internal cavities are drafted for support-free bridging. Clearances: The slip joint and nursery drop-in feature 0.3mm and 1.0mm radial clearances respectively. Assembly: Print the three pieces separately. Fill the Base Pedestal with dry sand, then seat the Capital Planter on top (use CA glue on the slip joint for a permanent bond). Drop the populated Nursery Insert into the top.
30mm Pump Stepped Fountain Spillway
A stepped water spillway that mounts to a standard 30mm aquarium pump outlet. Designed to convert a wide bowl into a trickling fountain for cats who require moving water. The fixture directs water up an internal bore and down a tiered ramp, generating continuous burbling surface disruption. Interface: 30.6mm internal diameter bore (sized for a slip fit on 30mm pump outlets), stopping at an internal collar at 20mm depth. Flow Channel: 60mm wide interior spillway. Descent Profile: Three sequential 8mm drop steps. Printability: Flat base and chamfered vertical edges. Prints without supports.
35x45mm Caster Wheel Brake
A heavy-wall retaining cup built to anchor rolling AC units and stop casters from wandering. Sized specifically for the caster drop-in footprint. Check your wheels before printing. Fitment Accommodates: Casters up to 35mm wide and 45mm long. Depth: 16mm of internal retaining depth (20mm overall minus a 4mm solid base). Wall: 4mm perimeter thickness to withstand machine weight without splitting.