Newar Lantern — Pagoda Temple Lamp
Created today
Description
The Newar Lantern is a miniature Newari-style Hindu pagoda temple built as a display lamp, standing 250 mm tall with a roof that overhangs a narrower temple body. The chamber inside is hollow and open at the front, with a 60 mm opening in the ceiling that drops LED light onto a separate Ganesh statue, while the cable runs in a ceiling channel, down a rear groove and out an 8 mm exit at floor level so the wiring stays out of sight. The three roof tiers lift straight off for access to the light and statue, and every piece sits on a flat bottom for stable printing.
Dimensions
- Assembled height: 250 mm
- Lower roof: 200 × 180 mm; base: 155 × 145 mm
- Internal chamber: 112 × 92 × 115 mm with a flat floor
- Arched front entrance: 105 × 105 mm, open at the front
- Ceiling light opening: 60 mm, with a recess for the LED holder
- Finial spigot: 12 mm
Features
- Three progressively smaller roof tiers with uppturned corner horns, layered eaves and a small windowed storey beneath the lower two
- A pointed finial seated in the top roof on a 12 mm spigot
- Two-step platform base with a row of 6 mm spherical ornaments
- Arched entrance with a framed, studded border, corner pillars, lattice side windows and a cornice
- LED holder: a flat plate with a collar for the module and a cable slot
- Separate seated Ganesh statue on a flat pedestal, about 90 mm tall and sized for the chamber
Print notes
- Seven pieces: temple body, three roof tiers, finial, LED holder and Ganesh statue
- Roof tiers join on 5 mm pins and 5.6 mm sockets, so they lift off without clips
- Roof undersides are set at a 45° slope so each tier prints without supports
- The sloped roof sections are solid rather than a thin shell — print them with 3 walls and about 8% infill, since the walls carry the load
- Flat bottoms keep every piece stable on the build plate
- Walls are kept to a minimum of 2 mm for durable printing
Photos
Technical views
More like this
Explore more in Decor & Display →
Classic Heart Shape, 7 mm Thick
What it's for A plain, symmetrical traditional Valentine's heart that prints flat on the plate as a single solid piece. Use it as a decorative shape, a gift topper, or a starting point for ornaments and hanging decorations. Classic rounded-lobe heart silhouette with a V-shaped notch at the top and a point at the bottom Each lobe is a true smooth arc, so the outline reads as a continuous curve from above with no flat facets The sides running down from the widest point to the bottom tip stay straight, as intended Front edges rounded all the way around, including both lobes Back face completely flat, with no edge rounding, giving a clean surface to glue against or to cut a mounting interface into Prints without supports Dimensions Width: 60 mm Height: about 55 mm (54.9 mm as measured on the plate) Thickness: 7 mm Edge rounding: 3 mm radius, on the front face only 60 mm is the largest direction, so the heart sits at the size limit rather than under it Print notes Lay the heart flat on the build plate so the 7 mm thickness forms the height and the flat back becomes the bed contact face. At this size it prints quickly and needs no supports or rafts. Any common filament works; a glossy or silk finish suits the smooth faces, and the rounded edge catches light along the outline. Remix ideas Add a small hole near the top lobe for hanging Emboss a name, date, or short message on the front face Cut a keyhole slot or a knob interface into the flat back for wall mounting or a stand Change the front edge radius for a puffier heart or more flat side wall
Tannenbaum — Adventskalender mit Steckdeckeln
Tannenbaum-Adventskalender mit 24 Fächern, erhabenen Zahlen 1–24 und Steckdeckeln mit Griffknopf. Der Baum hängt in der Ansicht an einer roten Wand mit Lichterkette, Kugeln, Schnee und Stern. Features 24 Fächer in Reihen 1–6 plus Stamm mit 3 Fächern Deckel mit Griffknopf und Steckzapfen, per Reibung gehalten Schlüssellöcher auf der Rückseite zum Aufhängen part = "scene" zeigt die Wanddekoration, nur zur Ansicht Print notes Zum Drucken part auf row1 bis row7 oder doors stellen Die Wanddekoration gehört nicht zum Druckteil
Flat Letter R, One Layer
A single capital R that is too thin for most letter stencils or tags to hold a clean edge, printed as one layer instead. It sits flat on the bed in Roboto, 13 mm text size and 0.12 mm thick. Print notes Text size: 13 mm (Roboto, capital R) Thickness: 0.12 mm, which is one layer at a 0.12 mm layer height Print slowly and lift it with a thin blade, since it has almost no stiffness No supports needed
Street Lamp Base with Domed Foot
A miniature street lamp base for a 1:64 diorama. A domed foot with a flat 7.2 mm bottom rises into a straight 5.5 mm shaft, 10 mm tall overall, with a centred 2 mm through-hole. Height: 10 mm Shaft diameter: 5.5 mm Foot diameter at the flat bottom: 7.2 mm Dome height: 6 mm Through-hole: 2 mm, fully open One solid body with a flat bottom, no decoration
Baby Dragon Figurine, 64x80 mm Base
A baby dragon figurine on a flat 64 x 80 mm base plate, built as one solid piece for FDM printing. Fit and print notes Four short legs, rounded body, small horns, tiny wings and a thick curved tail, all fused to the body. Check before printing: the bed must take about 64 x 80 mm. Prints without supports on its flat base in most cases. The horns and the wing tips are the only overhangs. Not scaled for any particular display stand or holder.
Engraved Name Block with Ogee Edges
A solid 4 x 3.5 x 1 in block with "Francisco Suarez" indented into the 4 x 1 in front face. All edges carry a Roman ogee profile: a concave sweep flowing into a convex bead. Size: 101.6 x 88.9 x 25.4 mm Name indented 1.5 mm, centered on the front face Smooth S-curve edge profile on all twelve edges Flat base, prints without supports