Armoured Oyster Bracelet Mid-Link
Created today
Description
A reinforced stand-in for a broken oyster-style solid link, with a crowned top and an R45 concave underside that follows the wrist. The hinge ends are built to take the load.
- Female end: two Ø5.2 ears around a 5.2 mm gap; male end: one Ø4.6 × 4.4 mm tongue.
- Ø1.6 pin bores, 35.8 mm pin to pin.
- Underside pocket stops 11 mm from centre, leaving solid hinge zones.
- Filleted webs where the ears meet the body.
- Ream the pin holes to 1.5 mm after printing.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.
Bracelet Octobre Rose 78mm
Un bracelet jonc simple et élégant, gravé du texte "OCTOBRE ROSE" en creux pour marquer l'événement sans nécessiter d'impression multicolore. Diamètre intérieur : 78 mm (ajusté pour un enfilage confortable) Épaisseur de paroi : 3 mm Hauteur : 12 mm Gravure : Découpée dans la paroi extérieure Impression : Conçu pour s'imprimer à plat sans aucun support
Slipbar — Snap-On G Cap
Slipbar G Cap is a standalone G-shaped cover that snaps onto the corners of a 68 × 38 × 10 mm rectangular buckle frame. The plate itself is the letter G, stretched to fill the frame's face, with a small clip at each corner. Features G-shaped plate, about 71.6 × 41.6 mm Four corner clips with small inward lips that catch the frame's lower edge Mirrored so the G reads correctly from the front face when printed face-down Print notes Print with the front face on the build plate PETG flexes best for the clips Test-fit the snap and adjust the lip if it is too tight or loose
3.2 mm Jump Ring Georgie Letter Links
Seven individual letter links spelling G-e-o-r-g-i-e, made to be joined by metal jump rings into a name bracelet. Fitment Each link is a 14 × 14 mm plate, 3 mm thick, with the letter raised 1.5 mm in Luckiest Guy. A 3.2 mm hole runs front to back through a round tab on each side, so a ring passes through the flat face. Hole centres are 19 mm apart on each link; adjacent links join with one jump ring through facing holes. Check before printing Jump ring wire must be under about 3 mm, or the holes will not take it. Does not fit Rings with wire thicker than 3 mm, or links with a closed clasp-style bail.
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.
Monolithic Grid Advent Calendar
A complete, print-in-place Advent calendar designed specifically to fit on the Bambu Lab A1 Mini (180x180x180 mm build volume). It features exactly 24 sliding drawers arranged in a space-efficient block, numbering from 1 to 24 sequentially. The top two rows contain 8 larger drawers perfect for bigger treats, while the bottom four rows hold 16 smaller drawers. Print-in-Place Design Ready to Slide: The drawers and frame are printed together as a single unit. Tolerances are tuned (0.4 mm on sides and bottom, 1.0 mm on top) so the bridging above each drawer naturally sags without fusing the parts together. Zero Assembly: No separate rails, glue, or snap-fit parts to mess with. Easy Grip: Each drawer features a neat little half-circle finger notch at the top, making them easy to pull open. Printing Tips No Supports: Do not generate supports, as they will fill the internal gaps and fuse the drawers to the frame. Cooling: Ensure your part cooling fan is running high so the bridges above the drawers stay relatively crisp. Material: Standard PLA works perfectly. White gives it a clean, classic winter look.