Description
Pad Plate is a flat base plate with a small raised square pad near one end, built as a clean surface for labels, stickers, or a colour swap. The pad is sized to sit comfortably on the plate and stays low enough to print cleanly in a few layers.
Dimensions
- Plate: 28.5 × 40 × 3 mm
- Pad: 11 × 11 mm, 0.7 mm thick
- Pad position: centred in X, 2 mm in from the Y- edge
Print notes
- 0.7 mm pad suits a 0.2 mm layer height at roughly 3 to 4 layers.
- Print flat, no supports needed.
- Pad and plate are separate colour regions, so a filament swap at the pad layer works well.
Images
More like this
Explore more in Decor & Display →
Extruder Figure on Cloud Plate
A printable extruder-style character lying on its back, standing in front of a solid 2 mm cloud plate. The name "Printytron" is raised on the body below the screen and is a separate part, so it can be coloured on its own. Boxy body with a recessed magenta screen showing a face with curved eyebrows and pupil indents Curved arms, thick hands, side box with teal button Hexagonal nozzle with a chunky square collar, flat on the plate Raised Space Mono lettering in its own colour Cloud backing plate whose bottom edge lines up with the hands and nozzle so the print can stand on a desk
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.
Teardrop Lamp Parts, Terracotta and Wood
A mid-century teardrop table lamp laid out as separate print pieces: fluted base, threaded crown collar, hollow prolate-spheroid diffuser and three dovetail-cleat prongs. A second set of the base, crown and prongs is included in a walnut-style wood tone, so one diffuser works with either finish. Remix hooks Wood finish: the wood set is the same geometry in a different colour. Print it in wood-fill or walnut-toned filament, then sand and oil it. Real grain would need a textured surface, which is a good next step. Fit: the thread clearance is about 0.4 mm and the cleat clearance about 0.3 mm. Adjust these to suit your printer. Bulb: it is sized for a 127 mm T10 or an ST19. The crown bore is 31 mm and the diffuser opening is 36.5 mm. Pairs with: an E26 socket, plus a small glue dab or set screw if you want the cleats locked. The tallest piece, a prong, is about 203 mm, so everything fits a 256 mm bed.
Welcome — Cursive Neon Strip Holder
Welcome is a script-lettered sign form with an open channel running through every letter, built for pressing flexible LED neon strip into place. Fill the channel, wire it up, and the flowing lettering glows like a custom neon sign. Features Heavy brush-style "Welcome" lettering 1.6 mm walls around an open top channel 2 mm floor, 10 mm overall height Wire exit holes through the floor at the ends of the word Print notes Prints flat with no supports Strip width varies by brand, so check the channel width against your strip first
Pumpkin Phantom Witch Hat Figurine
A friendly ghost rising from a jack-o'-lantern, topped with a chunky witch hat. A 70 mm single-piece figurine with a flat base and no fragile tips. Remix hooks Hat height: the cone is two stacked segments (10 mm and 8 mm); stretch them for a taller hat. Brim: 36 mm wide, 3 mm thick. Widen it, but add support beyond about 40 mm. Face: carved triangle eyes and a rectangular mouth on the pumpkin; swap in a toothy grin. Ghost arms: simple 8 mm round nubs. Lengthen them into waving arms. Pairs with: a round display plinth, or a tealight-sized base for a lamp variant.
Printytron Extruder Figure, 85 mm Wide
Desk figure of the Printytron character, styled after an extruder. It prints lying on its back, so the whole underside sits flat on the plate and no supports are needed. The body has a recessed magenta screen with a face (eyes with pupil indents, curved eyebrows, smile), a teal button on a side box, curved arms ending in round hands, and a hexagonal tapered nozzle on a square collar. "Printy.dev" is engraved below the screen. Specs Overall size: about 85 mm wide, 76 mm long, 15.5 mm tall as printed Orientation: back face down, screen facing up Body thickness: 14 mm; arms 5 mm thick; hands 10 mm thick Side box: sloped underside (about 50° from the plate) so it prints without supports Antennae: run down to the back face, so they print flat Nozzle: hexagonal cone with a flat underside along its full length, on a 22 mm square collar with a 1 mm bottom chamfer Engraving: "Printy" at 8 mm and ".dev" at 4 mm, Space Mono, about 1 mm deep Colours: yellow body, magenta screen, teal button; suited to a multicolour print or painting after printing