Standard Card Interlocking Holder
Created today
Description
A five-row holder for standard 63.5 × 88.9 mm playing cards. The deck tilts cards back at a 15-degree angle for easy reading without letting them spill.
The holder breaks down into two halves using a 3-tab interlocking jigsaw joint laid flat into the base. The base stays completely solid underneath to protect the cards, and the joint pulls straight apart vertically when you need to pack it away.
Specs
- Total Assembled Length: 330.2 mm (13 inches)
- Clearance: 0.25 mm per side on the interlocking puzzle tabs
- Groove Floors: Solid, minimum 3 mm thick beneath the slots
Images
More like this
Explore more in Storage & Organization →
130mm Tubeless Repair Kit Case
A rigid three-piece storage case designed for tubeless tyre repair kits. The base features an inset lip that locks the lid in place, secured by a snap-fit C-clamp latch that mounts to an integrated front axle. Dimensions: 130 mm x 85 mm x 35 mm combined. Wall Thickness: 2.5 mm throughout. Clearances: 0.3 mm on the lid slip-fit, 0.5 mm width clearance for the latch. Print Orientation: All three pieces are laid flat on the bed. No supports required.
4-Compartment Kitchen Organizer
A small, straightforward drawer organizer divided into four compartments. One wide compartment runs the length of the tray for standard utensils, while the back half is split into three smaller bays for loose items. Dimensions Overall size: 150 mm long × 100 mm wide × 35 mm tall Wall thickness: 2 mm solid walls and dividers Long bay: ~146 mm × 47 mm (ideal for small spoons or forks) Small bays: ~47 mm × 47 mm each Print notes Designed to print flat on its base without supports. Generous corner radii keep things from getting stuck in the corners. PLA or PETG both work fine for drawer use.
Cascading Hex Organizer
A minimalist, honeycomb-inspired desk organizer that steps up in height to hold everything from SD cards to tall pens. Its stepped layout is optimized for rapid support-free 3D printing. Zero Supports Required: Designed to print flat on the bed with no overhangs. V-Groove Details: Chamfered edges create a premium architectural look where the cells meet. Stepped Heights: Makes smaller items just as easy to grab as tall ones.
Standard 140x40 Gehäuse
Gehäuseunterteil mit Außenmaßen 140 x 40 x 25 mm und 3 mm Wandstärke. Passung: Der Deckel hat eine Innenlippe mit 0,5 mm Gesamtspielraum (0,25 mm pro Seite). Druck: Beide Teile liegen flach auf dem Druckbett (Deckel liegt auf der Oberseite) und benötigen keine Stützstrukturen. Kapazität: Innenraum misst effektiv 134 x 34 x 22 mm.
Ühe Otsaga Suletud Sahtlikarp
Sahtel kiilub kinni, sest pole kuskilt korralikult kinni võtta. See on suletud tagaseinaga lihtne kest, millel on nüüd sahtli ees korralik väike näpu-kõrgendus, et seda saaks mugavalt ja ilma küüsi murdmata välja tõmmata. Mahutavus: Täpselt 200 × 50 × 50 mm kasulikku ruumi. Seinad: 1.5 mm, prinditav ilma tugedeta. Liikumisruum: 0.5 mm lõtk külgedel tagab sujuva liugumise.
65mm Wood Hook Phone Bracket
A heavy-duty hook bracket to suspend a phone over a 60mm wooden beam or headboard. The main channel is sized at 65mm for clearance, dropping a device tray down 65mm from the top edge. Fitment: 65mm interior gap clears standard 60mm stock. Tray Specs: 16mm deep with a 3mm inward tilt to keep the device seated against the backrest. Width: 50mm overall extrusion. Printability: Designed to be printed flat on its side. Requires no supports.