Replacement Radio Knob
Created today
Description
The original plastic knob cracked and vanished years ago, leaving a bare metal shaft that digs into thumbs every time the volume needs adjusting. This replacement radio knob presses tightly over the stem to restore actual leverage. The perimeter is deeply fluted to prevent slipping when forcing a stiff old potentiometer, and a debossed pointer shows exactly where the dial sits without needing a second glance.
Fit and Dimensions:
- Outer envelope: 25 mm diameter, 15 mm depth.
- Shaft hole: 6 mm D-shaft footprint, recessed 12 mm.
- Alignment: The shaft flat sits 0.5 mm offset from the centre, positioned opposite the face pointer.
Images
More like this
Explore more in Home & Fixtures →
Anti-Spill Armrest Caddy
Sofa arms are basically designed to launch drinks onto the rug the second you shift your weight. This drops a rigid U-channel over the armrest to bridge the gap, locking down a flat staging plate on one side and a deep cup holder into the other. Specifications Total Length: 200 mm Inner Channel Width: 185 mm (verify this clears your sofa arm) Cup Holder: 80 mm diameter, 32 mm depth Print Specs: Prints hollow to save time and material. No supports needed if your bridging is dialled in.
Vileda Broom Bar Hook
Brooms that crash to the floor the moment a closet door closes are a solvable problem. This replacement end cap drops directly over a standard Vileda metal handle, replacing the stock hang loop with a massive, open hook that funnels right onto a closet bar without binding. The top arch features a flattened plateau. Flip the model onto this face in your slicer, and the entire assembly prints cleanly upside down without supports. Fitment Details Handle sleeve: 25.7 mm bore drops straight over the bare metal stick, seating the internal mushroom anchor. Hook clearance: U-channel accommodates hanging rods up to 27.5 mm. Print specs: Support-free when oriented on the flat top face; use PETG for impact resistance.
8mm Tank Bulkhead Fitting
M18 threaded bulkhead fitting engineered to pass an 8mm inner-diameter irrigation hose securely through a plastic tank lid. Interface: M18x2 thread with an independent hex locking nut. Sealing: Recessed O-ring groove on the interior flange face (2.5mm wide) to provide a watertight seal against the tank wall. Hose Barb: Double retaining barbs with a reinforced transition cone to handle clamping forces. Clearance: The hex nut is designed to slide freely over the 10.2mm barbs and internal threads are sized for clean printing in PETG. Both components are oriented to print flat on the bed without supports.
Ruined 85mm Column Planter
A functional planter designed to resemble a fragmented ancient stone column. The exterior features classical deep flutes and a stepped pedestal base, while the top rim and outer walls integrate geometric cutaways simulating heavy weathering and structural breaks. Specifications: Dimensions: 115 mm maximum base diameter, approximately 110 mm peak height. Cavity: 85 mm diameter bore with an 80 mm depth to house standard small nursery pots. Tolerances: Minimum 5 mm wall and base thickness maintained throughout all flutes and fracture geometry. Printability: Optimised for standard upright FDM printing; all destructive boolean cuts are angled to eliminate the need for supports.
TroughTrek — Modular Escape Ramp
A modular wildlife escape ramp built to saddle the rim of a 150-gallon stock tank. Designed to hang tight against the straight section of the wall, it leaves the center of the trough wide open while providing a secure path out of the water. Features Modular Assembly: Print the sections flat and slot them together using the flush integrated joints. Safe Traction: Half-cylinder ribs spaced evenly along the ramp offer grip without sharp edges that could catch paws or hooves. Dual Path: Includes both an inner descent into the water and an optional exterior ramp leading down to the ground. Rim Saddle: The central mount is contoured to slot cleanly over a standard 40mm rolled trough rim. Dimensions Width: 150mm (approx 6 inches) Incline: 35 degrees Segment Length: 300mm per section, yielding a ~344mm vertical drop per side (well below the typical waterline).
Blockhouse Sofa Console
A modular, flat-bottom console designed to bridge a couch cushion or rest flat on an ottoman. Built in two interlocking halves to clear a standard 250mm print bed, they join cleanly via six low-profile alignment pegs. Part A: Features two 80mm cupholder wells. Part B: A shallow recessed tray for snacks or plates, completely isolated from the joining mechanism so spills don't travel. Joinery: 25mm deep pegs and receivers, positioned low to leave the tray surface undisturbed. Add a little CA glue during assembly for a permanent hold.