Retro Soda Can Pen Cup
Created today
Description
Pop-art Americana meets desk organization. This stylized, flared-base replica channels the iconic silhouette of a vintage soda can, reimagined as a completely tip-proof desktop vessel. The deep maroon body bears embossed typography that conforms perfectly to the curved shell, while the aggressively flared bottom ensures your heaviest shears and tallest pens won't knock it over.
- Wide-Stance Base: A 96mm flared bottom eliminates the tipping hazard of standard cylindrical cups.
- Embossed Typography: Raised vintage lettering catches the light and adds a tactile element to the shell.
- Deep Well: Drops 115mm deep to securely cradle full-length pens, markers, and workspace tools.
Images
More like this
Explore more in Desk & Tech →
355ml Can Tray & Angled Desk Stand
Two-piece modular desk platform with a precision-fit dovetail seam. The main tray spans 250x160mm and runs four custom 68mm bores—sized specifically to drop in 355ml soda cans with exactly 1mm of clearance so they never bind. The extension plate mates flush to the right edge via four full-depth dogbone locks. It carries over the four cable passthrough notches and builds into an 89mm-tall backing plate offset precisely to set up a 15-degree resting angle off the main tray's front partition. Built with squared alignment edges against the seam and a solid side-stop block to lock your gear into place. Critical Dimensions Host Standard: 355ml standard soda can (66mm body). Overall Footprint: 500mm wide by 160mm deep (assembled). Seam Clearance: Locks are cut with 0.25mm of total gap so they seat tight without filing.
Retro TV Enclosure v2
A reinforced retro TV enclosure designed for an RP2040 video player project. The walls have been bulked up for extra durability without compromising the interior payload space, while side-firing one-inch speaker grilles and a classic bent antenna give it a finished look. What it's for Built to house a no-solder RP2040 media player. The clamshell locks together with an integrated friction fit and the entire model prints flat on the bed with zero supports. Dimensions Internal volume: 150 × 80 × 50 mm Wall thickness: 5 mm (beefed up from standard) Grilles: 25.4 mm (1 inch) perforated arrays on the left and right panels Assembly Both halves print cleanly flat. Slide your display into the front bezel's chamfered recess, route the cables out the back USB port, and firmly press the halves together until the interior ridges lock.
Assistive Smart Goggles Chassis
What it's for A wearable housing for smart glasses components, scaled to fit a human head. Features isolated electronic cavities, hollow arms for speakers and haptics, and integrated ports for front-facing cameras and downward sensors. Dimensions Overall Width: 150 mm Lens Housings: 52 mm tall, 18 mm deep Temple Arms: 11 mm wide, with a 30-degree drop behind the ear Assembly The frame and two arms print as separate flat-laid components without supports. Hinge tabs are modeled in — use short 3 mm pins or filament offcuts to join them.
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
Urgent Document Clip
A slim, low-profile clip meant to bind a few urgent sheets. Clearance: 0.5 mm pinch gap. Size: 40 mm wide for a firm hold. Print: Prints flat, face up, no supports.
Dev Board Lockdown Case
Raw development boards sliding across a desk are just waiting to short out on a stray screw or drop a jumper wire mid-compile. It’s annoying, it ruins components, and it makes moving a project impossible. This ends that. This is a clean, three-part enclosure built to lock down an ESP32 and an OLED display, keeping the wiring hidden and the desk clear. Footprint: 58.0 mm × 48.0 mm Total thickness: 34.5 mm (assembled) Display window: 30.5 mm square (designed for 1.3" OLEDs) Assembly: Uses four M3 screws driven from the back, leaving the front bezel perfectly clean. Print the three parts flat on their backs. Frosted PETG recommended if you want the board LEDs to diffuse through the case walls.