Right-Angle L-Bracket
Created 3 months ago
Description
A precision right-angle L-bracket designed for structural reinforcement, shelving, or frame assembly. The arms measure 50mm from the outer corner, providing a solid footprint for joining operations.
The model is oriented on its side by default. Printing the bracket in this orientation aligns the filament lines continuously along the L-shape, which maximizes bending strength and prevents snap-failures along layer lines.
- Dimensions: 50mm outer arm length, 15mm width.
- Material Thickness: 4mm uniform depth.
- Mounting: Two 5mm clearance holes, centered on the usable flat area of each arm.
- Print Settings: Minimum 3 walls/perimeters recommended for load-bearing applications.
Images
More like this
Explore more in Home & Fixtures →
Wall Shelf, 20 cm Glue-On
A small wall shelf that sits flat against the wall and glues on, with no drilling and no screws that miss the stud. The tall back plate gives the adhesive a big flat face, and two triangular gussets stop the front edge from sagging or peeling off. Key numbers Shelf top: 200 mm long x 80 mm deep x 4 mm thick Back plate: 200 x 40 mm, 4 mm thick, flat on the wall side Two gussets, 4 mm thick, each 34 mm tall Print: shelf upright on its back plate or flat on the top, no supports needed with the plate down; PETG or PLA, 3+ perimeters Glue: construction adhesive or mounting tape on the back plate face
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
Veranda Back Railing Bays
Railing section for the back half of the veranda, made to print separately from the deck base. It covers the long left side and the short end, with pickets running between a lower and a top rail. Left side bay with end post, plus the end-span railing across the back Pickets about every 110 mm at full scale Posts sit flat on the deck surface for gluing Same scale and position as the deck base, so the pieces line up