Rounded Square Mounting Plate
Created today
Description
A heavy-duty square spacer plate with a large central opening. The design features thick, continuous outer walls and uniformly rounded edges to prevent snagging and distribute load evenly.
Features:
- 110 mm square footprint with 35 mm depth
- 100 mm central through-hole
- 20 mm radius on all four outer corners
- Flat bottom profile for easy, support-free printing
Images
More like this
Explore more in Workshop & Tools →
7.1mm Bore Spacer Tube
Plain sleeve with a 9mm outer diameter and a 7.1mm through-bore. Length: 40mm Wall thickness: 0.95mm Measure the shaft or bolt this is going over before you run it. 7.1mm is a specific inside dimension, and FDM shrinkage usually eats a fraction of a millimeter on inner bores. With only a 0.95mm wall, there's not much material left to drill out if it runs tight.
Eğimli Üçgen Kama
Bu parça, arka tabanı 5 mm genişliğinde ve 1 mm yüksekliğinde olan, uca doğru eğimli bir şekilde azalarak sıfırlanan bir ikizkenar üçgen kamadır. Alt kenar uzunlukları istenildiği gibi tam 3.905 mm ölçüsüne denk gelir. Genişlik: 5 mm arka taban Yükseklik: 1 mm'den uca doğru sıfırlanır Kenar Uzunlukları: 3.905 mm (alt kenarlar)
4mm Square Key & Mount
The 4mm square key is the thing you can never find when a radiator needs bleeding or a panel needs opening. This gives the key a dedicated wall mount so it actually stays put. Includes a fitted bracket and custom printed M4 screws that use the same 4mm square drive as the key itself — meaning you don't even need a separate screwdriver to mount the bracket. Mounting bracket: 55mm × 15mm Key shaft: 4mm square Screw drive: 4.5mm square recess
60mm OD Flanged 45° Pipe
60mm outer diameter flanged pipe with a 45-degree elbow. Features a continuous 56mm inner bore with a 2mm wall thickness. The 100mm OD flange is positioned exactly 30mm from the base and runs 3mm thick. Check your clamp or mating collar against the flange thickness and 100mm outer diameter. No mounting holes are drilled; this part is built for bonded or slip-fit assemblies where the 56mm internal passage must remain entirely unobstructed.
Matix Snap-Fit Test Frame
Un piccolo frammento della scatola principale, isolato e progettato per essere stampato velocemente. Serve per testare fisicamente l'inserimento e lo scatto del frutto BTicino Matix prima di impegnare ore nella stampa del pezzo completo. Orientamento fedele: Si stampa in verticale, in modo che le linee di livello (layer) e i ponti della fessura riproducano esattamente le condizioni della scatola finita. Fianchi rigidi: Il profilo a "C" impedisce alla parete di flettere quando premi l'interruttore. Risparmio: Pochi grammi di filamento per verificare le tolleranze di aggancio.
Side-Pinned Click Lock 2 40-Quarter Dispenser
What it's for A fully mechanical, gravity-fed coin magazine tailored for standard U.S. quarters. It stores a full $10 roll vertically and dispenses exactly $1 (four quarters) per cycle into the palm of the hand. The mechanism relies on a two-stage sliding escapement, now utilizing a side-mounted limit pin to ensure the coin path remains entirely unobstructed during travel. Dimensions Overall Envelope (Dispenser): 34 × 56 × 75 mm (when closed) Slider Thickness: 7.2 mm Coin Bore: 25.2 mm (optimized for 24.26 mm quarters) Clearances Slider Play: 0.4 mm vertical clearance inside the track Pin Clearance: 0.3 mm on the locking pin diameter Cap Threads: 0.6 mm diametric clearance for smooth twisting Assembly The main body, slider, cap, and limit pin print separately without supports. Insert the slider into the main body track, align the side slot with the right-hand hole on the body, and push the limit pin flush into the side countersink to capture the mechanism. Remix ideas Threaded Cap: The top of the magazine tube features a coarse 4mm-pitch thread. Alter the tube height to make a shorter 20-coin version. Coin Bore: Tweak the internal offset diameter for other currencies or custom arcade tokens. Slider Thickness: Scaling the Z-dimension alters how many coins drop per pull.