Sink Caddy [DRAFT, NOT TESTED!]
Created 1 months ago
Description
To be printed and tested tomorrow.
A custom-fit sink caddy designed to straddle a 36.5mm sink divider. Features a skeletonized frame to save material and promote airflow.
- Sponge Basket: Deep right-hand basket tailored for sponges and chainmail scrubbers.
- Brush Cradle: Horizontal left-hand channel allows long-handled dish brushes to lay flat across shallow sinks.
- Drainage: Skeletonized walls and slotted floors ensure no standing water remains.
Images
More like this
Explore more in Kitchen & Bathroom →
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use
Cucharilla de dos piezas con conector
What it's for Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas. Dimensions Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor. Alojamiento: 16 × 6 mm, 23 mm de profundidad. Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic. Ventanas laterales de 4 mm donde se aloja el resalte. Remix ideas Añadir una cabeza de cuchara en la pestaña tope del conector. Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme. Cambiar el radio de curvatura del mango.
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.