Sleeve — 0.385" OD Spacer Tube
Created today
Description
Sleeve is a plain, precise hollow cylinder sized in inches: a straight-through bore and a clean outer wall, ready to use as a spacer, bushing or standoff.
Dimensions
- Outer diameter: 0.385" (9.78 mm)
- Inner diameter: 0.26" (6.60 mm)
- Length: 0.75" (19.05 mm)
- Wall thickness: about 0.0625" (1.59 mm)
Print notes
- Print standing on end, no supports needed.
- Bore may print slightly tight; ream or scale up a touch if fit matters.
Images
More like this
Explore more in Workshop & Tools →
Hex Tube 40 mm Tall With Center Bore
A hex tube, 4 cm tall, for when a round spacer or standoff spins or rolls where a flat-sided one would hold still. The 2.5 mm bore runs the full length so a rod, wire or screw passes straight through. Key dimensions Height: 40 mm Width: 5.15 mm point to point Center bore: 2.5 mm diameter, through the full length Printing Print standing upright, no supports needed. Walls are thin at the hex flats, so use at least 2 perimeters and a small nozzle if possible.
69 mm Round Spacer, 5 Holes
A round spacer 69 mm in diameter and 10 mm tall with a 40 mm center bore and five 5.5 mm through-holes on a 54 mm bolt circle. Outer diameter: 69 mm Height: 10 mm Center hole: 40 mm Bolt holes: 5 × 5.5 mm on a 54 mm circle Hole spacing: 68°, 72°, 72°, 68°, 80° (the 80° gap is between the last and first hole) Prints flat with no supports
door lock
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm". Overall size: 100 x 24 x 15 mm Groove: 16 mm wide x 11 mm deep, open at both ends Side walls: 4 mm; floor: 4 mm Engraving: 0.6 mm deep, readable from above Prints flat with no supports
outside hat
A plain flat disc in the spirit of an oversized washer or a vinyl-record blank: 3 inches across, 1/8 inch thick, with a clean 1 cm hole through the centre. Prints flat with no supports. Diameter: 76.2 mm (3 in) Thickness: 3.175 mm (1/8 in) Centre hole: 10 mm Good for spacers, coasters, templates, or as a base for other builds
Klipper Display and Status Console
Compact left-side mounting enclosure for Klipper printer telemetry, designed specifically for the Ender 3 Pro 2040 vertical extrusion. Hardware Compatibility: Fits a 1602A I2C LCD, a 32x32mm HW-109 MAX7219 LED Matrix, and a standard 5mm RGB LED. Internal Clearance: 36mm cavity depth cleanly clears standard I2C backpacks. Mounting System: Left-oriented 5mm side flange using dual slots for M4 t-nuts. Flange sits flush to the bottom, leaving top clearance for gantry travel. Assembly: Snap-fit 2mm front panel with internal screw bosses; back plate secured via four M3 interior corners. The housing prioritises rigidity and short wiring paths over bulk, anchoring firmly without compromising structural frame limits.
Zauberstab 3.5
What it's for Zweiteiliger Zauberstab mit Griff und Spitze für eine UV-Taschenlampe. Außen ist ein glatter Stab mit schmalen, aufgelegten Teigsträngen, die sich spiralförmig um ihn winden. Innen verschließt ein Bajonett mit Rastnocke. Dimensions Griff: 87 mm hoch, 85 mm Innenhöhe, Bohrung Ø 21,8 mm Spitze: 135 mm gesamt, verjüngt sich nach oben, Lichtkanal innen hohl Glatter Kern Ø 26,4 mm, vier Stränge, ca. 0,8 mm breit am Boden und nach oben schmaler Vier Löcher Ø 3,75 mm im Boden Remix ideas Mehr oder weniger Stränge Stränge dicker für stärkeres Relief Andere Windungszahl über die Höhe