Sloped Power Box Enclosure3
Created 1 months ago
Description
A sloped-console enclosure for a custom battery power box.
The case features a sloped front panel for mounting a DSN-VC288 volt/amp meter and a generic battery level indicator, positioning them at an ergonomic viewing angle.
- Outputs: Four 14 mm barrel jacks on the front panel.
- Inputs: One 14 mm barrel jack and a 17×12 mm power switch cutout on the rear.
- Internals: A segregated 70×60 mm battery compartment with retaining walls.
- Assembly: Four M3 corner bosses meant for heat-set inserts, securing a drop-on top plate.
Images
More like this
Explore more in Desk & Tech →
Lazy-Tongs Piano Bottle Caddy
A pantograph-style drink arm in the spirit of a vintage lazy-tongs: a hooked clip straddles the top of a piano's music desk, and a three-unit scissor mechanism unfolds backward to carry a bottle cup. The cup sits inside a wide, rimmed drip tray, so condensation stays off the keys and cabinet. The arm folds flat for storage and stretches out for use. Pivots are print-in-place pins, and the two end joints ride in slots so the arms can open and close. Design notes Cup bore is 76 mm, sized for a standard 33.8 fl oz (1 L) water bottle; cup wall is 85 mm tall. Drip tray is 96 mm across with a 12 mm rim and sits flush with the arm plane. Clip slot fits a music desk about 13 mm thick; adjust the thickness value to suit your piano. Three colored regions: desk clip, scissor arms, cup and tray. Shown in a partly extended pose; the opening angle can be changed to show it folded or fully reached. Best printed as shown, with 0.4 mm clearances at the pivots. Support is only needed under the clip hook. A full bottle is a cantilever load, so keep the arm short for heavier bottles.
Handheld-Gehäuse mit herausnehmbarer Anschlussblende
Handheld-Gehäuse für eine selbstgebaute Konsole, bei dem die Kabel- und USB-Öffnung hinten nicht dauerhaft offen bleibt: Eine Klipp-Platte schließt sie und lässt sich bei Bedarf herausnehmen. Aussparung in der Rückwand: 100 × 30 mm, mittig Klipp-Platte: Außenrand 104 × 34 mm, Einsatz 99,6 × 29,6 mm, zwei Federarme mit Rastnasen, Fingermulde Innentiefe: 48 mm, Wandstärke 3 mm Display-Fenster 155 × 87 mm, Tastenlöcher 7,2 mm Druck: Schalen offen nach oben, Platte flach, ohne Stützen möglich
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
Urgent Document Clip
A slim, low-profile clip meant to bind a few urgent sheets. Clearance: 0.5 mm pinch gap. Size: 40 mm wide for a firm hold. Print: Prints flat, face up, no supports.
Speaker Dust Cap 14mm
Exposed speaker voice coils attract dust and metal particles until they grind themselves to death. This replacement dust cap seals the center of a 50mm driver without adding enough mass to ruin the high-frequency response. Footprint: 14mm diameter base to perfectly match standard 50mm driver coils. Profile: 4mm spherical dome for rigidity. Mass: 0.3mm shell thickness, designed to print as a single perimeter. Mounting: Sliced flat at the absolute bottom zero to provide a clean, continuous rim for CA glue or rubber cement.
Vertical Arc Reactor Speaker Stand
What it's for A vertical, upright stand designed to hold an Echo Dot 3rd Gen while transforming it into a glowing reactor core. The custom cavity is deep enough to cover the sides of the device entirely, leaving only the top surface and the signature light ring visible from the front. A bottom channel allows the power cable to route straight down seamlessly. Dimensions Base: 120 × 100 mm footprint for vertical stability. Speaker Cavity: 101.5 mm diameter, 44 mm depth (tailor-made to enclose the puck). Overall Height: ~150 mm. Print notes Orientation: Prints best as oriented. Ensure your bridging settings are dialed in for the speaker cavity and the rear acoustics hole. Supports: You may want light supports under the bottom edge of the ring and inside the cable channel, depending on your printer's overhang capabilities. Assembly: Slide the Echo Dot in from the front, route the barrel plug up through the bottom slot, and plug it in.