Created today
Description
A raised plinth for the Snapmaker U1 that turns the space under the printer into a five-slot build-plate rack with four drawers beneath. The overall body is 380 × 380 × 110 mm, and the top carries a shallow 3 mm recess to locate the printer's feet. It is an add-on base, not a replacement for a printer part.
The plate slots in the upper tier are 276 mm wide and 6 mm tall, sized for 270 × 270 mm plates with a little play, separated by 3.5 mm shelves. Ejection now happens from the front: each of the five slots has a pull-slider on its right-hand side — a slim bar in a groove cut into the slot wall, with a hook at the back sitting behind the plate and a rounded knob at the front. Pull the knob forward about 12 mm and the hook drags the plate out; push it back to reset.
Underneath, four drawers about 89 mm wide and 180 mm deep are shortened from a full-depth layout, leaving a solid block behind them that carries the printer's weight.
Photos
Technical views
Raised base for the Snapmaker U1, 380 × 380 × 110 mm overall, with five build-plate slots in the upper tier and four drawers underneath. It is an add-on base, not a replacement for a printer part. The top has a shallow 3 mm recess to locate the printer’s feet. The plate slots are 276 mm wide and 6 mm tall, sized for 270 × 270 mm plates with a little play, and separated by 3.5 mm shelves. Each slot has an eject pushbutton: a pin through the back wall with a round head, pushed in to move the plate about 12 mm out the front. The pins are separate pieces and sit loose in their holes; add a small clip or a dab of glue to keep them in place. The four drawers are about 89 mm wide and 180 mm deep, shortened from the earlier full-depth layout; the solid block behind them carries the printer’s weight. The eject pins project about 15 mm behind the 380 mm body, so leave that clearance behind the base. Fit check Fits: Snapmaker U1, with five build plates around 270 × 270 mm. Check before printing: measure the U1’s actual footprint and foot spacing. The 380 mm outer size and the 3 mm deep foot recess depend on that measurement. Confirm plate size against the 276 mm slot width and 6 mm slot height. Not universal: other printers need the base resized. Plates wider than the slots or thicker than 6 mm will not fit as intended. Print bed: the 380 mm frame exceeds most common print beds, so it needs a large-format printer or splitting into sections.
Letrero con el texto "Arecson Dj" en relieve sobre una base rectangular plana de 2 mm. Pensado como placa o rótulo sencillo para un puesto de DJ, con letras en Montserrat fáciles de leer. Dimensiones Base: 90 × 24 × 2 mm Letras: 4 mm de relieve sobre la base Tipografía: Montserrat, tamaño 13 Notas de impresión Imprime plano, sin soportes. Las letras pueden hacerse de otro color cambiando de filamento en la capa 2 mm.
Caja con tapa y orejetas de cierre, ajustada para imprimirse en una cama de 220 × 220 mm como la de la Ender 3 Pro. El cuerpo mide 203 mm de largo y las orejetas ya no sobresalen tanto, así que cada pieza queda en 217 mm de ancho. Detalles Interior de 193 × 95 mm. 4 orejetas con agujero para insertos roscados M6. Tapa con solapa y ranura para junta de goma. Placa vertical con refuerzos. A tener en cuenta Cada pieza se imprime por separado; en el modelo aparecen una al lado de la otra solo para la vista.
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Caja con tapa para insertos roscados M6 en cuatro orejetas de cierre, con medidas interiores de 200 × 95 × 40 mm y paredes de 5 mm. Qué lleva 4 orejetas exteriores con agujero de 8,4 mm y 8 mm de profundidad para insertos roscados M6 de 9 mm de diámetro exterior. Tapa de 10 mm de grosor con 4 agujeros avellanados de 6,4 mm. Solapa de tapa de 70 × 40 mm, con 10 mm de grosor y esquinas superiores con radio de 15 mm. Lleva un agujero central de 8 mm y otro de 6 mm a 25 mm del centro. Ranura de 1,5 mm en caja y tapa para un cordón de goma de unos 2 mm. Placa vertical de 60 mm con triángulos de refuerzo de 3 mm de grosor. Medida a comprobar El diámetro exterior real de los insertos. El agujero está pensado para 9 mm. No encaja Tornillos distintos de M6 en las orejetas, ni cordones de goma de más de 3 mm.
这是一套需要组装的、可多层叠加的茶包抽屉,按 PLA 打印设计:底座框架内装两组定滑轨与动滑轨,抽屉盒体沿轨抽出,前端用两颗 D4×2 磁铁吸合,四角堆叠卡扣让相同单元上下定位。打印件包括底座、抽屉盒体、动/定滑轨各 2 件、4 个堆叠卡扣和抽屉端板;组装用 M3×8 平头螺栓。 可改的起始尺寸 底座框架:140×110×32 mm,后部开窗;侧壁 3 mm。 抽屉盒体:外尺寸 126×98×26 mm;前壁 2 个 Φ4 磁铁沉孔,设计深 2.2 mm。 滑轨:定/动滑轨各 2 件,长 110 mm;动定之间留 0.2 mm 滑动间隙。滑轨为 2 mm 薄片,受底座侧壁厚度限制。 堆叠卡扣:42×18×14 mm,四角各一件;抽屉端板:106×28×6 mm。 紧固孔:M3 沉头过孔 Φ3.4 mm;磁铁:D4×2 mm。 换版时先动这几处 先改抽屉盒体的长宽高,底座和端板跟着放量,滑轨长度保持 110 mm 或按新行程加长。 0.2 mm 滑动间隙是抽拉手感的关键,材料收缩大时先调这里,不要先改轨形。 堆叠卡扣的 42×18×14 mm 决定层间定位;要叠更高或换更厚板材,优先改卡扣高度与卡口深度。 磁铁沉孔按 Φ4×2.2 mm 设计;想换 D5 或 D6 磁铁,直接放大沉孔与对应磁铁位。 M3 沉头孔为 Φ3.4 mm 过孔,螺栓头不会完全埋平;需要齐平就加深或扩大沉孔。 如果要继续做系列,这套盒体适合与同尺寸底座、不同深度的抽屉盒,以及带标签孔的端板配对;保持四角卡扣和滑轨接口不变,就能混搭层数。