SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Snapmaker U1 Raised Base with Drawers

Created today

Storage & Organizationsnapmaker-u1raised-basebuild-plate-storageeject-pinsshortened-drawersrear-clearancelarge-formatsplit-print
Remix this model →

Remixed once

Description

Raised base for the Snapmaker U1, 380 × 380 × 110 mm overall, with five build-plate slots in the upper tier and four drawers underneath. It is an add-on base, not a replacement for a printer part. The top has a shallow 3 mm recess to locate the printer’s feet.

The plate slots are 276 mm wide and 6 mm tall, sized for 270 × 270 mm plates with a little play, and separated by 3.5 mm shelves. Each slot has an eject pushbutton: a pin through the back wall with a round head, pushed in to move the plate about 12 mm out the front. The pins are separate pieces and sit loose in their holes; add a small clip or a dab of glue to keep them in place. The four drawers are about 89 mm wide and 180 mm deep, shortened from the earlier full-depth layout; the solid block behind them carries the printer’s weight. The eject pins project about 15 mm behind the 380 mm body, so leave that clearance behind the base.

Fit check

  • Fits: Snapmaker U1, with five build plates around 270 × 270 mm.
  • Check before printing: measure the U1’s actual footprint and foot spacing. The 380 mm outer size and the 3 mm deep foot recess depend on that measurement. Confirm plate size against the 276 mm slot width and 6 mm slot height.
  • Not universal: other printers need the base resized. Plates wider than the slots or thicker than 6 mm will not fit as intended.
  • Print bed: the 380 mm frame exceeds most common print beds, so it needs a large-format printer or splitting into sections.

Images

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Snapmaker U1 Raised Base with Drawers

Snapmaker U1 Raised Base with Drawers

A raised plinth for the Snapmaker U1 that turns the space under the printer into a five-slot build-plate rack with four drawers beneath. The overall body is 380 × 380 × 110 mm, and the top carries a shallow 3 mm recess to locate the printer's feet. It is an add-on base, not a replacement for a printer part. The plate slots in the upper tier are 276 mm wide and 6 mm tall, sized for 270 × 270 mm plates with a little play, separated by 3.5 mm shelves. Ejection now happens from the front: each of the five slots has a pull-slider on its right-hand side — a slim bar in a groove cut into the slot wall, with a hook at the back sitting behind the plate and a rounded knob at the front. Pull the knob forward about 12 mm and the hook drags the plate out; push it back to reset. Underneath, four drawers about 89 mm wide and 180 mm deep are shortened from a full-depth layout, leaving a solid block behind them that carries the printer's weight. Design notes Front-eject sliders: 4 mm thin and 380 mm long, so they flex — print them flat. Hook engagement: the hook only meets the plate's back edge, so it won't catch a plate pushed in past it. No rear overhang: with the pins gone, nothing projects behind the 380 mm body any more. Clearance: pull the knob forward roughly 12 mm of travel per slot. Fit check Fits: Snapmaker U1, with five build plates around 270 × 270 mm. Check before printing: measure the U1's actual footprint and foot spacing — the 380 mm outer size and the 3 mm foot recess depend on it. Confirm plate size against the 276 mm slot width and 6 mm slot height. Not universal: other printers need the base resized. Plates wider than the slots or thicker than 6 mm will not fit as intended. Print bed: the 380 mm frame exceeds most common print beds, so it needs a large-format printer or splitting into sections.

10 hours agoRemix →
模块化滑轨可堆叠茶包抽屉

模块化滑轨可堆叠茶包抽屉

这是一套需要组装的、可多层叠加的茶包抽屉,按 PLA 打印设计:底座框架内装两组定滑轨与动滑轨,抽屉盒体沿轨抽出,前端用两颗 D4×2 磁铁吸合,四角堆叠卡扣让相同单元上下定位。打印件包括底座、抽屉盒体、动/定滑轨各 2 件、4 个堆叠卡扣和抽屉端板;组装用 M3×8 平头螺栓。 可改的起始尺寸 底座框架:140×110×32 mm,后部开窗;侧壁 3 mm。 抽屉盒体:外尺寸 126×98×26 mm;前壁 2 个 Φ4 磁铁沉孔,设计深 2.2 mm。 滑轨:定/动滑轨各 2 件,长 110 mm;动定之间留 0.2 mm 滑动间隙。滑轨为 2 mm 薄片,受底座侧壁厚度限制。 堆叠卡扣:42×18×14 mm,四角各一件;抽屉端板:106×28×6 mm。 紧固孔:M3 沉头过孔 Φ3.4 mm;磁铁:D4×2 mm。 换版时先动这几处 先改抽屉盒体的长宽高,底座和端板跟着放量,滑轨长度保持 110 mm 或按新行程加长。 0.2 mm 滑动间隙是抽拉手感的关键,材料收缩大时先调这里,不要先改轨形。 堆叠卡扣的 42×18×14 mm 决定层间定位;要叠更高或换更厚板材,优先改卡扣高度与卡口深度。 磁铁沉孔按 Φ4×2.2 mm 设计;想换 D5 或 D6 磁铁,直接放大沉孔与对应磁铁位。 M3 沉头孔为 Φ3.4 mm 过孔,螺栓头不会完全埋平;需要齐平就加深或扩大沉孔。 如果要继续做系列,这套盒体适合与同尺寸底座、不同深度的抽屉盒,以及带标签孔的端板配对;保持四角卡扣和滑轨接口不变,就能混搭层数。

1 day agoRemix →