Description
A heavy-duty rear kicktail platform designed for the Escoone W6 electric scooter. Features a solid, uninterrupted core for maximum strength, adjustable bolt spacing for the 114.3mm factory mounts, and a steep ramp angle to lock in the rear foot during hard acceleration.
- 105mm bottom arch to clear the rear fender
- Solid center spine for FDM printability
- Recessed bolt mounts to keep the deck flat
- High-traction chevron cuts for grip
Images
More like this
Explore more in Automotive, RC & Hobby →
GOpro fieur skadis
A sturdy, mechanical mount that attaches standard GoPro gear to an IKEA SKÅDIS pegboard. Unlike standard static mounts, this design features a vertical hinge axis allowing the camera to pan left and right, making it ideal for overhead workspace recording or fixed security angles. The design relies on an M5 bolt and nut to clamp the vertical rotation axis firmly in place once the angle is set. The quick-release buckle block prints separately for optimal layer orientation, plugging into the rotating base plate. Assembly Base: Locks into two standard SKÅDIS slots without tools. Mechanism: Insert an M5 bolt through the side clamp, trap an M5 nut in the hex recess, and tighten with the printed knob. GoPro Buckle: Glues or presses onto the two registration pegs atop the rotating platform. Slide your standard GoPro helmet buckle straight in.
Snap-Fit Poultry Band
A heavy-duty, flex-to-fit poultry leg band designed for easy application on turkeys. Customizing the Fit Band Diameter: Currently scaled for roughly a 1-inch (25.4mm) leg, making it suitable for mature turkeys. Band Width: The height along the leg is half an inch (12.7mm). The Hinge: The back of the ring thins out to 1mm to create a living hinge. You can thicken this if your material is exceptionally soft, or thin it further if you are using a stiffer PLA. The Lock: Features a horizontal bulb snap-fit. The locking pin squeezes through the entry gap and clicks into an enclosed cavity, keeping it secure even during movement. Adjust the bulb diameter or cavity clearance depending on your printer's tolerance.
Lego piece for wagon door runner with thinner teeth bit slightly smaller
Wagon door runner to replace 3 off 15208 bricks Version with slightly too large slope
Sistema de Dirección Ackermann2
Sistema de dirección frontal mecánico tipo Ackermann, diseñado para vehículos a radiocontrol o maquetas. Las manguetas descansan sobre el eje rígido principal y se conectan mediante una barra de acoplamiento, asegurando que la rueda interior trace un radio de giro más cerrado que la exterior durante las curvas. Puntos de Modificación Este diseño está pensado como una plataforma base para integrarse en chasis personalizados. Las cotas actuales sirven como punto de partida: Ancho del eje: 100 mm totales, con 90 mm entre los centros de pivote. Geometría Ackermann: Los brazos de dirección tienen una longitud de 20 mm y un ángulo de inclinación interna de 15 grados. Tornillería: Los orificios en el eje y la barra son pasantes de 3.2 mm, mientras que las manguetas cuentan con orificios de 2.8 mm diseñados para que tornillos M3 muerdan directamente en el plástico. Ejes de rueda: Los vástagos laterales miden 5 mm de diámetro por 18 mm de largo, compatibles con rodamientos estándar de RC 5x10 o hexágonos adaptadores.
Sweeping Dollhouse Window Slide
A large 3D-printable playground slide designed to mount securely into a 90 mm window frame, sized for 1:6 scale dolls. The track follows a single smooth clockwise sweep out and away from the dollhouse, transitioning cleanly to the floor. Broad Descent: Uses a smooth Bezier sweep to drop 460 mm without looping or reversing direction. Upright Geometry: The track remains perfectly level across its width from top to bottom. Window Mount: Features a squared notch that drops cleanly over a standard lower window edge.
240mm Kidney Pool With Slide Receiver
A 1:6 scale kidney-shaped pool basin optimized for flat build plates, featuring an integrated U-channel slide receiver on the front edge. The structure prints as a single monolithic part with no overhangs requiring support material. The basin wall is swept to provide a soft 3mm top bevel, and the interior floor transitions via a 4mm chamfer to prevent sharp 90-degree corners that trap water or dirt. Dimensional Specs Max Footprint: 240 mm × 175 mm (fits standard 256 mm build volumes). Basin Height: 50 mm overall; 44 mm usable interior depth. Wall Thickness: 10 mm continuous structural wall. Slide Interface: 70 mm wide channel with 15 mm vertical retention walls and exactly 15 mm of socket depth to positive stop. Base Plate: Solid 6 mm thick floor, printing entirely flat to the bed.