Spider Web Plaque with GARTH Name
Created today
Description
What it's for
A flat spider web ornament with the name GARTH raised across its centre. Suitable for wall hanging, Halloween decor or a themed gift.
Dimensions
- Web diameter: about 132 mm
- Thickness: 2 mm web, 4 mm with lettering
- 12 spokes, 4 concentric rings, hanging loop at top
- Lettering: 10 mm size, Permanent Marker font
Remix ideas
- Swap the name or change the font
- Add a plush spider on a ring
- Scale down for a keychain or ornament
Images
More like this
Explore more in Decor & Display →
Balance Coffee Raised Letter Sign
A flat rectangular sign with raised "BALANCE COFFEE" lettering in Archivo Black, sized for a shelf, counter or wall. Remix hooks Plate size: 140 × 40 × 4 mm with a 1 mm chamfer. Widen it for a longer sign, or stack the two words on two lines and make the plate taller. Letter height: 2 mm raise, text size 11. Go to 1 mm for a quicker print, or 3 mm for stronger shadows. Colours: the plate and letters are separate regions. Print with a filament swap at layer 4 mm for a two-tone sign. Mounting: no holes yet. Add two screw holes near the ends, or a rear slot for hanging. Pairs with: a small stand or a wall bracket.
Pumpkin Phantom Witch Hat Figurine
A friendly ghost rising from a jack-o'-lantern, topped with a chunky witch hat. A 70 mm single-piece figurine with a flat base and no fragile tips. Remix hooks Hat height: the cone is two stacked segments (10 mm and 8 mm); stretch them for a taller hat. Brim: 36 mm wide, 3 mm thick. Widen it, but add support beyond about 40 mm. Face: carved triangle eyes and a rectangular mouth on the pumpkin; swap in a toothy grin. Ghost arms: simple 8 mm round nubs. Lengthen them into waving arms. Pairs with: a round display plinth, or a tealight-sized base for a lamp variant.
Heart Plaque With Levy and Leny
A heart-shaped plaque with two raised names, "Levy" on the upper line and "Leny" directly below it. The names are raised so they can be read by sight and by touch, and nothing else is written on the piece. Print details Heart footprint: about 85 × 78 mm Total height: about 10.3 mm (9 mm stepped, domed body plus 1.3 mm of lettering standing proud) Lettering: raised, printed as one piece with the heart Print flat, base down, with no supports needed Two colours are possible with a filament change at the lettering layer
Kristallkugel auf Podest mit Öse
What it's for Wahrsager-Kristallkugel im klassischen Kinderzeichnungs-Stil: glatte Kugel auf einem gestuften Podest, in einem Stück gedruckt. Die Öse oben erlaubt zusätzlich das Aufhängen an Angelschnur. Dimensions Kugel: Ø 100 mm, hohl, Wand 2,4 mm Podest: Fuß Ø 110 mm, Gesamthöhe bis Kugelsitz 30 mm Gesamthöhe ca. 115 mm, passt auf eine 180×180-mm-Platte Schnurloch: Ø 3,5 mm Remix ideas Sterne oder Mondsymbole in den Podestfuß prägen Öse entfernen für reine Standversion Kugel größer oder Podest höher skalieren
Halloween Gravestone Trophy V5
A Halloween trophy gravestone that prints as separate pieces, because a single-colour solid block makes white lettering and a skull impossible. The black stone and pedestal print in black PLA. The skull, webs, bats, cross and lettering print in white PLA and plug into sockets in the stone, so nothing relies on glue alone for position. Numbers that decide fit Assembled size: about 160 mm tall, 90 mm wide, 35 mm deep (pedestal 90 × 35 × 22 mm; stone 80 × 18 mm, arch radius 40 mm). Stone-to-pedestal joint: two rectangular tenons, 8 × 10 mm and 12 mm long, at offset positions so the stone only goes in one way. Pedestal holes are 8.5 × 10.5 mm and 14 mm deep, leaving 2 mm of glue space. Small parts: 2.8 mm pegs, 4 mm long, with chamfered tips. Sockets are 3.1 mm wide and 5 mm deep. Lettering: three word plates (BEST VILLAIN, HALLOWEEN NIGHT, WROCŁAW • 24.10.2026). Each has a 1.2 mm backing plate that sits in a recess, letters raised 1.8 mm and two pegs. Surface: chipped edges and cracks are modelled into the stone. Printing Stone: print it back-down, flat. Pedestal: print it upside-down or bottom-down. No supports are needed for either. White parts: print the lettering face-down, with the pegs pointing up. Print the skull, webs, bats and cross back-down. The model includes an assembled view and an exploded view. Each white part sits on its own socket pattern. Assembly: fit the tenons into the pedestal, glue them, then press each white piece into its sockets and glue.
Mandarin Community Town Model
A tabletop town for practising Mandarin place words, where flat labels get lost. Each building, sign and park area carries its Chinese characters, pinyin and English on the front face, so the vocabulary sits right on the thing it names. Details that matter Base: 200 × 200 mm, 4 mm thick plate Buildings: hospital, library, community center, store and school, each 46 × 28 mm footprint Extras: park with pond, road, footpaths, houses, cars, trees, lamps and figures Colour regions: ground, road, walls, roofs, doors, lettering, signs, trees, lawn, pond, paths Print: large bed needed (or scale down); multicolour or paint by region; lettering is 0.8 mm raised, so use a 0.4 mm nozzle