Stage-Ready Drum Rack Tablet Console
Created 1 months ago
Description
A heavy-duty tablet console designed to mount directly to the horizontal crossbar of a standard electronic drum rack. Built with the working drummer in mind, this holder leans back at a comfortable reading angle for sheet music apps, metronomes, or playback tracks, and features an extra-deep lip to secure tablets in thick protective cases.
Setup Notes
- Mounting: Snaps over any standard 1.5" (38.1mm) drum rack tube.
- Hardware: Requires two M6x40mm (or longer) bolts and matching M6 hex nuts to lock the clamp tight. The flanges include recessed hex traps so you only need one wrench to tighten them.
- Printing: For maximum strength against drum vibrations, lay the model flat on one of its side faces (so the large circular hole points straight up) during slicing. This aligns the layer lines along the clamping arm, making it virtually indestructible. No supports are needed in this orientation.
Photos
Technical views
More like this
Explore more in Desk & Tech →
Arcade Console Desk Clock Case
A compact desk-clock enclosure with a gaming-rig attitude: chamfered shoulders, vented flanks and grooved front stripes under the OLED window, like a mini console from a late-night LAN party. Window for a 0.96" OLED on the front Standoffs for an ESP32 WROOM-32 devkit USB slot at the back Four corner screw bosses and a separate screw-on lid Side vent slots for airflow
Ten-Port Keystone Panel With Fan
A 270 × 61 mm mounting panel with a 60 mm fan opening on the left and ten snap-in keystone ports on the right. A rounded, squircle-style notch is cut into one long edge near the right end. Remix hooks Notch span: runs from 216.25 mm to 258 mm along X, 15.25 mm deep in Y. Move either end to resize it. Corner radius: both inner corners use a 7 mm radius. Raise it for a softer shape; keep it under about 7.6 mm to stay within the notch depth. Corner material: the notch stops at 258 mm, leaving the right-end 3.5 mm mounting hole (5 mm from the end) fully surrounded. Keystones: 14.5 × 16 mm openings with a 1.8 mm front lip and rear clip relief. Dimensions are provisional, so test one jack before printing all ten. Pairs with: a cable-management bar or a fan grille over the 58 mm vent. It's meant for a particular 12U rack.
Fan and Keystone Mounting Plate
A 270 x 61 mm flat plate, 4 mm thick, combining a 60 mm fan mount with a row of ten keystone jack openings. The fan opening sits at the left end with four screw holes on the standard 50 mm spacing. The right side carries ten rectangular openings on an 18 mm pitch for standard keystone jacks. A 3.5 mm mounting hole sits 5 mm from each end on the centerline. Plate: 270 x 61 x 4 mm Fan: 56 mm opening, 4.3 mm screw holes at 50 mm spacing Keystones: 10 openings, 14.8 x 19.8 mm Mounting: 2 x 3.5 mm holes
Fidget Spinner Planetario Ø70 mm
Fidget spinner a ingranaggi planetari stampabile in un solo pezzo (print-in-place), diametro esterno 70 mm, con ingranaggio solare centrale, 5 satelliti e anello esterno dentato internamente. L'anello è alleggerito da 10 fori passanti e non ha coperchi, così gli ingranaggi restano visibili. Diametro esterno: 70 mm, spessore 8 mm Modulo 1,5; solare 15 denti, satelliti 10 denti, corona 35 denti Denti elicoidali a spina di pesce (25°) che trattengono i satelliti senza assi Gioco sui denti: 0,25 mm Fori centrali Ø7 mm (solare) e Ø5 mm (satelliti) per alleggerire Stampa piatta, senza supporti; PLA o PETG
Foldable Snap-Fit Phone Stand
A rugged, fully printable foldable phone stand. It is printed in three flat pieces that snap together securely, allowing it to fold completely flat for travel. Features Adjustable Angles: Features 7 resting notches on the base plate to precisely control the screen angle. Snap-Fit Hinges: Uses C-clip snap joints that grip firmly onto 6mm pins without requiring any extra hardware. Travel-Ready: Folds down to a flat profile when not in use. Print Instructions Print flat on the bed as oriented. Standard PLA or PETG works perfectly. Ensure good bed adhesion for the flat plates. The snap-fit hinges are designed with a 0.4mm clearance — they will require a firm push to snap into place during assembly, but will hold tight thereafter.
ESP32 Enclosure with 1.3 Inch OLED Lid
Two-piece enclosure for a 30-pin ESP32-WROOM-32 DevKit V1 with a 1.3 inch SH1106 OLED mounted in the lid. Shown exploded with heat inserts and M3 screws aligned to the corner holes. The lid has a 35.5 x 34.5 mm recess on the underside that holds the OLED PCB, and a 35.5 x 20.5 mm window through the front panel for the visible display area. ESP32 pocket: 52 x 28 mm, 14 mm deep Outer size: about 56.8 x 40.4 mm, 2.4 mm walls Front USB-C slot, 10 x 4 mm Four corner screw holes for M3 screws and heat inserts Front panel thickness behind the window: 1.6 mm Print the lid face-down for a clean front surface.