Tapered Plug For salt shakers
Created 1 months ago
Description
A solid tapered plug to replace the rubber foot that vanished from the chair leg three moves ago, ending the tilt that sends your coffee sliding across the desk. It wedges directly into a standard hollow tube or serves as a standalone standoff.
Dimensions for fit:
- Base diameter: 10 mm (the wide end sitting on the floor)
- Top diameter: 7 mm (the narrow end driving into the socket)
- Height: 8 mm clearance
Images
More like this
Explore more in Home & Fixtures →
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
G 1 1/4" Plug with Concave End
What it's for A male-threaded plug for a G 1 1/4" (BSP parallel) port, such as a bull nose fitting. The end face is dished (concave) so it seats against a rounded nose. Dimensions Thread: G 1 1/4", 41.91 mm major diameter, 2.309 mm pitch (11 TPI) Thread length: 20 mm Hex head: 50 mm across flats, 10 mm tall Concave dish: 30 mm sphere radius, 5 mm deep Remix ideas Change the dish radius or depth to match a different nose profile. Add a gasket groove under the hex head. Swap the hex for a knurled round head for hand tightening.
горшок илья
A solid-walled, 140mm tall flower pot with subtle vertical waves along its tapered exterior. The base tapers from a 120mm top opening down to 105mm at the bottom, featuring a robust 4mm thick floor and exactly eight 6mm drainage holes to keep soil adequately drained. Remix Hooks Wall Thickness: Currently 3mm, cleanly subtracted from the inner radius so the exterior waves never break through. Wave Amplitude: Set to 1.5mm with 24 peaks around the perimeter; you can scale the amplitude up for a deeper scallop or increase the frequency for a ribbed texture. Drainage Pattern: The 8 holes sit on a 60% radius ring; this is an easy block to swap out if you prefer a slotted grid or a single large center hole. Scale Factor: The linear extrusion uses a calculated 120/105 ratio. Tweaking this lets you flare the pot wider or pull it into a straight cylinder.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)