Tapered Tunnel Adapter 20x23 to 19x19
Created today
Description
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening.
Key numbers
- Large end outer size: 20 x 23 mm
- Small end outer size: 19 x 19 mm
- Length: 7 mm
- Wall thickness: 0.6 mm
- Open all the way through
Printing
- Print standing on the large end, no supports needed
- Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters
- No clearance is added; scale slightly if the hole is tight
Images
More like this
Explore more in Home & Fixtures →
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Y-Rohrstück 75 auf 39 mm mit Steckende
Y-Rohrstück, bei dem ein weiteres Rohr auf dem oberen Ende nicht richtig sitzt, weil kein gerades Stück zum Aufstecken vorhanden ist. Der obere Abschnitt hat jetzt ein 20 mm langes gerades Ende mit 39 mm Außendurchmesser. Unterer Teil: 75 mm Außendurchmesser, 30 mm lang Konus: 30 mm lang, von 75 auf 39 mm Steckende oben: 39 mm Außendurchmesser, 20 mm lang Abzweig: 39 mm Außendurchmesser, 48° zur Rohrachse, schneidet die obere Öffnung nicht Wandstärke: 2 mm überall Druck: aufrecht auf der 75-mm-Öffnung, der Abzweig braucht Stützen
Advent Calendar Drawer With Grip
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip. Remix hooks Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling. Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square. Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers. Fit: trim 0.2 mm off width and height if it binds in the frame. Pairs with: the other numbered drawers, since the front footprint is unchanged.
Konischer Rohradapter 34 auf 26 mm
Konischer Rohradapter, 65 mm lang, mit gleichmäßiger Verjüngung von Innen-Ø 34 mm auf Innen-Ø 26 mm. Die Stirnkanten sind mit 1 mm Radius abgerundet, damit die Oberfläche glatt ist und sich Schläuche leichter aufstecken lassen. Länge: 65 mm Innen-Ø Anfang: 34 mm, Innen-Ø Ende: 26 mm Außen-Ø Anfang: 40 mm, Außen-Ø Ende: 32 mm Wandstärke: 3 mm (horizontal gemessen) Kantenradius an den Stirnseiten: 1 mm Druck: stehend auf der großen Öffnung, ohne Stützen
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
Eccentric Duct Adapter 125mm
What it's for Bathroom duct adapter that connects a round duct to a flat rectangular duct. Both ends are female sockets, and the airflow passage is fully open. The round socket has a wide bore for a loose, free fit. Dimensions Round socket: Ø142.5 mm inner, Ø147.3 mm outer, 30 mm long, 1.5 mm entry chamfer Flat socket: 222 × 92 mm inner, 5 mm corner radius, 30 mm long Transition: 160 mm, smooth round-to-rectangle loft Vertical offset of the flat socket: 72.5 mm Wall thickness: 2.4 mm Overall length: 220 mm Remix ideas Change the bore diameter to tune the fit for a different duct. Adjust the vertical offset for another mounting position. Lengthen the sockets for a deeper grip.