Made by a Guest
Created today
Description
Open-top rectangular bin, 210 x 112 x 85 mm, split into three equal compartments side by side. Outer and divider walls are 3 mm thick and each compartment has a 4 mm floor.
The name CHARO is a separate raised piece, 1.5 mm thick, that sits flat against the front wall. Print it on its own and glue it in place, or print it in a second colour.
Images

Open-top storage box with three equal compartments side by side, and the name CHARO raised across the full front face. Outer size: 210 x 112 x 85 mm Walls and dividers: 3 mm Floor: 4 mm Compartments: 3, each about 66 x 106 mm inside Lettering: Bebas Neue, about 200 x 77 mm, raised 1 mm on the front Prints upright with no supports
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.

What it's for A four-compartment cutlery separator tray for a drawer, with semi-round finger cutouts in each divider so utensils lift out easily. Dimensions Overall height: 30 mm, with a 3 mm base and 3 mm walls Three compartments 240 mm long: 50, 60 and 65 mm wide One 55 mm wide, 185 mm long compartment beside the 65 mm one Finger cutouts: 24 mm diameter semicircles centred on each divider Remix ideas Change the cutout radius for deeper or shallower scoops Split the tray into pieces for smaller print beds Add a lip or feet for drawer grip
A three-tier slatted shoe rack, 500 × 300 × 480 mm, holding six pairs (two per shelf), now with decorative trim. Remix hooks Side diamonds: 22 mm diamond cutouts on each side panel, two per tier. Change the size, count or shape (hexagon, circle) to taste. Scalloped crown: 30 mm half-round bumps along the top of the back panel, spaced 50 mm. Widen the spacing for a calmer look. Corner finials: 18 mm spheres on the four top corners. Swap for cones or pyramids. Pairs with: splitting into panels for printing; the 8 mm wall suits dowel or screw joints. Dimensions to keep: shelf spacing (40/190/340 mm) sets shoe clearance.
PivotTee è un portabrugole piatto per chiavi a T da 10 a 3 mm, con perni laterali che lo fanno ruotare da orizzontale a verticale su una base da fissare al cassetto. Un fermo girevole dietro il blocco lo tiene in verticale durante l'uso, e il perno centrale accoglie un inserto filettato M3 per avvitare il fermo. Caratteristiche Otto sedi da 10 a 3 mm con fessura superiore e numeri incisi Base con due fori svasati da 5 mm Perno del fermo da 8 mm con foro da 4,2 mm per inserto M3 (profondità circa 8 mm) Fermo girevole 44 × 14 × 6 mm Print notes Tre pezzi stampati sdraiati, senza supporti Inserto filettato da scaldare a caldo nel foro del perno
Spiral shoe rack with six 60° steps around a central column on a round base, one pair of shoes per step. Each step has a dovetail tongue that slides down into a matching slot in the column, so steps can be removed or attached individually. Steps: 18 mm flat plates, 4 mm outer lip, 90 mm rise per step Overall size: 600 mm diameter, 540 mm tall Base: 300 mm diameter, 12 mm thick, chamfered Clip: dovetail 15 mm deep, 0.3 mm slot clearance Removal: lift the step straight up Print steps flat; column upright; large size may need scaling or sectioning