Vault display
Created 1 months ago
Description
A heavy, stepped display stand built to hold trading cards, toploaders, and graded slabs securely. The open-sided 15-degree slot accommodates wider custom cases without binding, and the front face features a prominent, raised "VAULT 208" emblem.
- Format Agnostic: Open sides mean it handles everything from raw sleeves to oversized slabs.
- Stable Base: The stepped block profile adds mass right where it’s needed to keep top-heavy slabs firmly planted.
- Bold Lettering: Embossed stencil lettering stands completely proud of the front face.
Images
More like this
Explore more in Decor & Display →
FLAGE MAROCAINE
A precisely dimensioned 180x120mm base for a Moroccan flag assembly. The model features an accurate 1mm-deep recess carved as five intersecting straight lines, capturing the true geometry of the traditional interlaced pentagram. Through-holes at the five intersecting tips provide exact alignment for a matching drop-in star, while doubling as push-out points if the star needs to be removed after test-fitting. Specifications Dimensions: 180 mm x 120 mm x 3 mm Recess Depth: 1.0 mm (maintains a 2 mm solid floor) Alignment: Five 2.4 mm diameter positioning through-holes Print Settings: Prints flat on its back; no supports required
Flat-Print A4 Picture Frame
A clean, single-piece A4 picture frame designed to print flat on large beds (like 360x360mm). It prints face-down to ensure a smooth front finish and requires zero supports. Integrated Keyholes: Built-in flush mounts for both portrait and landscape orientation. Drop-in Retainers: Six small twist-clips print alongside the frame in the empty center space. They drop into the pre-drilled holes on the back to lock your paper and cardboard backing firmly in place. Generous Recess: The back channel allows up to 2.5mm of clearance, leaving plenty of room for standard A4 paper paired with a corrugated cardboard or stiff card backing.
Nelore BCS Display Base
What it's for A structured, segmented display base designed to present five cattle models demonstrating Body Condition Scores (BCS). Features an elegant multi-tiered design with distinct angled platforms, giving each figure a dedicated presentation space without structural clutter. Dimensions Overall footprint: 400 mm length x 100 mm width. Total height: 20 mm (10 mm main base, 5 mm middle tier, 5 mm individual platforms). Display pads: 65 mm x 40 mm, offset at a 25-degree angle. Split halves: 200 mm length each, designed to fit cleanly on standard 256x256 mm print beds. Print notes Orientation: Print both base halves flat on their bottoms. Print the pegs horizontally as oriented in the file for maximum shear strength across the layer lines. Clearances: The dowel holes are 8.4 mm with 8.0 mm pegs. This 0.2 mm radial clearance is generous enough for easy assembly straight off a standard FDM printer, but tight enough to hold firmly with CA glue. Supports: None required. All chamfers and geometries are optimized for direct bed printing.
Cutaway Gearbox Desk Display
A cutaway gearbox in the spirit of a museum engineering sectional: a boxy housing with the front and top sliced open so the meshing gears and cross shafts sit in plain view. Two spur gears (14 and 22 teeth) on 6 mm shafts Open front and top reveal the mesh Shafts pass through the housing sides Flat base plate for stable desk display Pairs well with a small crank on one shaft.
Helix — Open-Frame Twisted Fin Lamp Shade
Helix is a flared lamp shade with no solid wall. 72 thin fins spiral through a 60° twist as the shade widens from the base to the top, and three low reinforcing rings hold the whole frame together. The result reads like a lantern or woven cage, and the light comes through as spiralling slats of shadow. The fins and rings are matched on purpose: each fin reaches inward only as far as the rings do, so the inner edge stays clean from bottom to top. A small spoked fitter ring at the base seats the shade over a lamp holder. Dimensions Height: 130 mm Base diameter: about 90 mm Top diameter: about 140 mm Twist: 60° over the full height Features 72 twisted, flared fins, 1.2 mm thick Three low-profile rings at the bottom, middle and top, 3.5 mm tall Fin depth matched to the ring depth (about 6.6 mm at the base, scaling with the flare) Spoked fitter ring at the base, 3 mm tall Print notes Print upright with the fitter ring on the plate. Slow speeds help, since the fins are thin. Use a cool LED bulb only. Fit to a specific socket is untested, so check the fitter ring against your holder.
Flush Citrus Bow Tie
A wearable multi-colour bow tie featuring flush-inlaid citrus slices that are trimmed perfectly to the tie's outer edge. The base is 3mm thick, swapping to the fruit colours halfway up for a clean flush surface. Remix Hooks Scale the Slots: The elastic slots are exactly 2.5mm by 15mm. If you're using thicker strapping, dial that square size up before printing. Tweak the Layout: The position, size, and rotation of every slice is driven by a central data array, making it simple to pack them tighter or scatter them further. Shape the Tie: The bow tie shape is driven by a rough polygon and smoothed via aggressive offset passes; change the offsets if you want a sharper, more geometric profile.