Visor — Smart Goggles Chassis Set
Created today
Description
Visor is a printable smart-goggle chassis kit: a front frame, two hollow temple arms, an electronics box and matching caps, laid out flat for printing.
Features
- Frame with two lens-housing cavities, camera ports and downward sensor holes
- Hollow arms with speaker slots, USB-C opening and power switch cut-out
- Electronics box with lipped lid
- Frame cap: a one-piece back cover with two lips that plug into the eye cavities (0.3 mm clearance per side)
Print notes
- Every piece prints flat without supports.
- Arms join the frame with 3 mm pins or filament offcuts.
Images
More like this
Explore more in Decor & Display →
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.
Christmas Tree Lantern for LED Tealight
A Christmas tree lantern that sits over a battery LED tealight, so the light stays hidden inside instead of glaring from a bare tealight on the table. The walls are perforated with rings of small round holes that throw dots of light, and the bottom is open so the LED can be placed or swapped without taking anything apart. Key numbers Height: about 135 mm including star Base diameter: 90 mm, open underneath (inner opening about 87 mm) Wall: 1.6 mm, three stacked tiers Perforations: 4.2 mm holes, staggered rings Star: separate colour, peg-mounted into the top tier Printing Print upright, open end down, no supports needed for the cone walls Green for the tree, gold or yellow for the star Use a 0.4 mm nozzle; a lighter or translucent filament glows more
Klassisk spillebrik uden support
En traditionel spillebrik til brætspil som gåsespil: bred rund fod, aftagende kegleformet krop, en lille krave og et kugleformet hoved. Samlet højde ca. 33 mm, fodens diameter 22 mm. Hele brikken printes stående uden support. Remix-muligheder Fodens diameter (22 mm): gør den bredere for mere stabilitet, eller mindre, hvis felterne på brættet er små. Højde: kroppen er 14 mm høj. Forlæng den for en mere slank brik, der er nem at gribe. Hovedet (14 mm kugle): skift til en terning, en cylinder eller et nummer, så hver spiller kan kende sin brik. Farve: print i forskellige filamentfarver, eller lav et hul i bunden til en lille magnet eller en vægt. Passer til andre brætspil, hvor brikkerne skal stå på felter på ca. 25 mm eller mere.
Teardrop Lamp Parts, Terracotta and Wood
A mid-century teardrop table lamp laid out as separate print pieces: fluted base, threaded crown collar, hollow prolate-spheroid diffuser and three dovetail-cleat prongs. A second set of the base, crown and prongs is included in a walnut-style wood tone, so one diffuser works with either finish. Remix hooks Wood finish: the wood set is the same geometry in a different colour. Print it in wood-fill or walnut-toned filament, then sand and oil it. Real grain would need a textured surface, which is a good next step. Fit: the thread clearance is about 0.4 mm and the cleat clearance about 0.3 mm. Adjust these to suit your printer. Bulb: it is sized for a 127 mm T10 or an ST19. The crown bore is 31 mm and the diffuser opening is 36.5 mm. Pairs with: an E26 socket, plus a small glue dab or set screw if you want the cleats locked. The tallest piece, a prong, is about 203 mm, so everything fits a 256 mm bed.
Watch Bracelet Mid-Link 14 x 31 mm
Replacement mid-link for a metal watch bracelet, 14 mm wide and 31 mm long, with a crowned top, a forked female hinge end and a single-tongue male hinge end. Pin holes are 1.6 mm for reaming. The underside is pocketed to save material. Body: 14.0 x 31.0 x 3.4 mm, 1.4 mm edge fillets Crown: raised 0.8 mm above the body top Female end: two 5.2 mm diameter ears, 5.2 mm slot Male end: 4.6 mm diameter tongue, 4.4 mm wide Pin holes: 1.6 mm, at Y = ±17.9 (35.8 mm pin to pin) Underside pocket: 1.9 mm deep, 0.7 mm corner radius Wrist curve not applied; exported flat Intended for PETG, printed bottom face down
Pad Plate — Offset Square Marker
Pad Plate is a flat base plate with a small raised square pad near one end, built as a clean surface for labels, stickers, or a colour swap. The pad is sized to sit comfortably on the plate and stays low enough to print cleanly in a few layers. Dimensions Plate: 28.5 × 40 × 3 mm Pad: 11 × 11 mm, 0.7 mm thick Pad position: centred in X, 2 mm in from the Y- edge Print notes 0.7 mm pad suits a 0.2 mm layer height at roughly 3 to 4 layers. Print flat, no supports needed. Pad and plate are separate colour regions, so a filament swap at the pad layer works well.