Walkable SPD-SL Cleat Cover
Created 3 months ago
Description
What it's for
A slip-on protection cover designed for Shimano SPD-SL road cycling cleats. It prevents slipping on hard surfaces like wet cafe tiles while protecting the plastic cleats from premature wear off the bike.
- Features a deep, cross-hatched tread pattern on the sole for traction.
- An internal tapered lip locks the cover securely over the top edge of the cleat hardware.
- A solid rim surrounds the treads to prevent the edges from catching while walking.
Dimensions
- Internal Layout: 75mm long by 55mm wide at the heel, matched to standard SPD-SL profiles.
- Side Walls: 3mm thick for lateral rigidity and protection.
- Base: 4mm thick solid sole, structured to accommodate 2.5mm deep tread grooves.
Materials
Printing this model in a flexible filament like TPU is strongly recommended. The flexibility allows the inner retaining lip to stretch over the cleat body during installation and removal, while the rubber-like material provides the necessary slip resistance.
Remix ideas
- Adapt the internal cavity geometry and overall footprint to fit Look Keo or standard SPD cleat profiles.
- Replace the cross-hatched tread with aggressive horizontal lugs or a custom dot pattern.
- Add a small tether loop to the heel end to leash the covers together when stored in a cycling jersey pocket.
Images
More like this
Explore more in Automotive, RC & Hobby →
Flat Snap-In Interior Trim Cover
A removable interior trim cover with a flat front surface, a stepped outline (107 mm wide at the top, 123 mm at the bottom, 180 mm tall) and a soft raised area at the upper left. A rear locating frame and eight ratcheting snap clips hold it in the opening without screws. Remix hooks Raised area height: 10 mm with a roughly 30 mm blend. Lower it for a subtler step, or delete it for a fully flat panel. Surface curvature: the panel is flat in both directions. A gentle crown can be added back by adding a term to the height function. Clip layout: four clips per side at 25, 65, 105 and 145 mm height, each with four ratchet teeth 3.5 mm apart. Change the tooth pitch to match the metal edge thickness. Stabilising grid: 20 mm pitch, 1.6 mm ribs, about 3.5 mm tall. Pitch and height are easy to adjust. Pairs with: fuzzy skin in the slicer for a textured plastic look, in PETG, ASA or ABS.
25mm Tactical Tabletop Tokens
A complete set of nine 25mm wargaming tokens tailored for tabletop tracking. Designed with a clear separation between the base and the raised lettering, making them perfectly suited for a mid-print filament swap or a multi-material system. Specifications Dimensions: 25 mm diameter, 4 mm overall height. Tolerances: The raised text and outer rim sit exactly 1 mm above the base layer, creating a clean Z-height transition for color changes. Printability: No supports required. The bottom edges feature a 1 mm chamfer to prevent elephant-foot distortion on the first layer, ensuring the tokens remain perfectly circular and easy to pick up from flat tables. Layout: Arranged in a flat 3x3 grid for immediate batch printing. Can be split into individual models in the slicer if needed.
OO Gauge semi detached house stone v2
A semi-detached stone house pair in OO gauge, printed as separate pieces: front wall with quoins at the outer ends, mitred side walls, a one-piece roof, a floor piece, two chimneys, and separate window and door inserts. Four small locator rails now help position the side-wall tabs on the front wall. Remix hooks Tab locators: four U-shaped pieces, each 6.8 × 18.6 × 1.5 mm. Glue one against the inside of the front wall beside each side-wall tab. The 0.3 mm clearance around the 15 × 5 mm tab is the value to tune for your printer. Locator thickness: 1.5 mm now. Raise it for a firmer stop. Window and door inserts: 3 mm thick, 0.2 mm clearance per side. Pairs well with: a thin plasticard base or a printed street baseboard.
Line Follower Chassis, N20 Drive
What it's for A line-follower chassis plate with N20 motor cradles, an adjustable-height front sensor tray, an ESP32 mount, a battery holder, a driver mount, a rear caster tab and an LED hole. Dimensions Overall: about 130 × 198 mm, under 25 mm tall (the plate sits 8 mm off the ground). Motor cradles: 12.2 × 24.7 mm pocket for a 12 × 10 × 24.5 mm N20, with a shaft notch and two M2 holes each. Wheel cutouts: sized for 34 mm wheels with more than 2 mm clearance to the plate. Sensor tray: 126 × 26 mm board shelf, two vertical M3 slots in the riser for height adjustment. ESP32: four standoffs for a 48 × 26 mm board, plus two zip-tie slots. Battery: 68 × 18 × 19 mm pocket along the axle line, two strap slots. Driver: two zip-tie slots for a 21 × 18 mm module. LED: 5 mm hole near the rear edge. Wiring: two 10 mm slots between the motor mounts and the electronics. Remix ideas Add a cover clamp across each motor cradle using the M2 holes. Change the caster tab hole spacing for a different caster. Add a second sensor tray for a different board width.
Saipa Pride 111 Clock Bezel Phone Cradle
Preliminary replacement for the Saipa Pride 111 (2011 / 1390) dashboard clock bezel, with a landscape cradle for the Samsung Galaxy A54 5G. All bezel dimensions are placeholders and not taken from the car. Fit status Host: Saipa Pride 111 clock opening. Bezel size, spigot depth and clip positions are placeholders. Phone: Galaxy A54 5G, 158.2 × 76.7 × 8.2 mm, plus 3 mm case allowance and 1 mm clearance per side. Does not fit other Pride trims or other phones. Measure before printing Dash opening width, height, depth, corner radius and clip or screw positions. Notes The cradle is wider than the clock opening, so it projects forward of the dash. Open-top slide-in loading, side lips, a bottom ledge and a USB-C side slot. Tilt is 15° back. Check it against the dash and your sight line. Print in ASA or PC-CF. PETG softens in a hot parked car.
Domed Wickiup Terrain Shelter
A hollow dome structure designed to represent a wickiup or wigwam shelter. Useful as tabletop terrain or a diorama element. Overall Size: 100 mm diameter footprint Structure: 3 mm wall thickness Features: Domed exterior, arched front entryway, and a central top vent hole Base: Sits flat on the build plate for easy printing