Wall Shelf, 20 cm Glue-On
Created today
Description
A small wall shelf that sits flat against the wall and glues on, with no drilling and no screws that miss the stud. The tall back plate gives the adhesive a big flat face, and two triangular gussets stop the front edge from sagging or peeling off.
Key numbers
- Shelf top: 200 mm long x 80 mm deep x 4 mm thick
- Back plate: 200 x 40 mm, 4 mm thick, flat on the wall side
- Two gussets, 4 mm thick, each 34 mm tall
- Print: shelf upright on its back plate or flat on the top, no supports needed with the plate down; PETG or PLA, 3+ perimeters
- Glue: construction adhesive or mounting tape on the back plate face
Photos
Technical views
More like this
Explore more in Home & Fixtures →
110x80mm Invertible Wall Shelf
A simple, sturdy wall shelf with a subtle rim on the underside, designed so it can be mounted inverted. Features a 110x80mm flat area and integrated reinforcement gussets for rigidity against the wall. Dimensions: 110mm width x 80mm depth. Mounting: Twin countersunk screw holes on the backplate. Features: 3mm retention lip and dual structural gussets.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Lifebuoy — Wall Key Rack
Lifebuoy is a wall-mounted key rack shaped like a beach lifeguard buoy, with a red body, white LIFEGUARD lettering and five sturdy hooks. Features 230 mm long stadium-shaped body, 70 mm tall, 14 mm deep Letters as a separate white piece set into a pocket in the red body Five round-tipped hooks along the lower front Two rear keyhole-style screw holes with counterbores Flat back for printing without supports Print notes Print the body and the letters in separate colours (PLA, 0.4 mm nozzle), back face down.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Dragon Head Blind Cord Cleat
Blind cords slip off a plain cleat the moment the tension changes. This dragon head cord cleat has a tusk on each side of the snout, so the cord wraps under it and stays put. Mounting plate: 30 x 70 mm, 4 mm thick, two countersunk screw holes Tusks: ball-tipped, project about 16 mm out from the centre on each side, above the cord path Cord slot: 3.5 mm tall, runs left to right through the snout Flames: three tongues from each nostril, pointing forward over the plate Extras: horns, brow ridges, cheek spikes Print: plate flat on the bed; the horns and flames are small overhangs, so a little cleanup or supports may help
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.