Watch Bracelet Mid-Link 14 x 31 mm
Created today
Description
Replacement mid-link for a metal watch bracelet, 14 mm wide and 31 mm long, with a crowned top, a forked female hinge end and a single-tongue male hinge end. Pin holes are 1.6 mm for reaming. The underside is pocketed to save material.
- Body: 14.0 x 31.0 x 3.4 mm, 1.4 mm edge fillets
- Crown: raised 0.8 mm above the body top
- Female end: two 5.2 mm diameter ears, 5.2 mm slot
- Male end: 4.6 mm diameter tongue, 4.4 mm wide
- Pin holes: 1.6 mm, at Y = ±17.9 (35.8 mm pin to pin)
- Underside pocket: 1.9 mm deep, 0.7 mm corner radius
- Wrist curve not applied; exported flat
- Intended for PETG, printed bottom face down
Images
More like this
Explore more in Decor & Display →
Posable Dragon With Friction Joints
A posable toy dragon that holds its pose, with detailing so it doesn't look like a plain chain of balls. The old version looked like a bare stick of linked beads. This one adds belly plates, scale studs and a trimmed base. What's on it Cream belly plates under each body link Dark-red scale studs along both flanks, plus the back spike row Raised gold trim around the edge of the base Same 12 ball-jointed body links and ball-jointed head Print notes 0.2 mm joint clearance: raise it if the joints fuse, lower it if they sag Print in PETG for repeated bending Multi-colour print or paint the belly plates, trim and spikes
14 x 14 x 13 mm Palm Cavity Hand
A stylised hand with the middle finger extended and the other fingers folded, with a square 14 × 14 mm cavity, 13 mm deep, centred in the palm. Fit and check Cavity: 14 × 14 mm opening, 13 mm deep, open on the palm side, blind (does not exit the back of the hand). Palm is 22 mm thick, leaving about 9 mm of material behind the cavity floor. Measure the cavity after printing if a 14 mm part must fit; FDM usually shrinks holes slightly. Not included No reference image was available, so proportions are generic. Fingernail is a small raised plate on the back of the middle finger. It does not show from the palm side. Scaled compact, about 104 mm tall, so it is not life-size.
Mandarin Community Town Model
A tabletop town for practising Mandarin place words, where flat labels get lost. Each building, sign and park area carries its Chinese characters, pinyin and English on the front face, so the vocabulary sits right on the thing it names. Details that matter Base: 200 × 200 mm, 4 mm thick plate Buildings: hospital, library, community center, store and school, each 46 × 28 mm footprint Extras: park with pond, road, footpaths, houses, cars, trees, lamps and figures Colour regions: ground, road, walls, roofs, doors, lettering, signs, trees, lawn, pond, paths Print: large bed needed (or scale down); multicolour or paint by region; lettering is 0.8 mm raised, so use a 0.4 mm nozzle
Anel de Guardanapo com Cruz
Anel de guardanapo com cruz à frente, para o tecido não escorregar nem ficar solto na mesa. A cruz fica separada do círculo e presa por uma ponte sólida, em uma peça única. Diâmetro interno do anel: 45 mm, parede de 3 mm, altura de 5 mm Cruz: 50 mm de altura, haste de 12 mm de largura e 5 mm de espessura Ponte de ligação: 8 mm de largura, 12 mm de altura Impressão FDM em PLA; a parte de baixo do anel elevado pode pedir suporte
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.
Teardrop Lamp Parts, Terracotta and Wood
A mid-century teardrop table lamp laid out as separate print pieces: fluted base, threaded crown collar, hollow prolate-spheroid diffuser and three dovetail-cleat prongs. A second set of the base, crown and prongs is included in a walnut-style wood tone, so one diffuser works with either finish. Remix hooks Wood finish: the wood set is the same geometry in a different colour. Print it in wood-fill or walnut-toned filament, then sand and oil it. Real grain would need a textured surface, which is a good next step. Fit: the thread clearance is about 0.4 mm and the cleat clearance about 0.3 mm. Adjust these to suit your printer. Bulb: it is sized for a 127 mm T10 or an ST19. The crown bore is 31 mm and the diffuser opening is 36.5 mm. Pairs with: an E26 socket, plus a small glue dab or set screw if you want the cleats locked. The tallest piece, a prong, is about 203 mm, so everything fits a 256 mm bed.