Wavy Bobby-Pin Sock Clip
Created today
Description
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece.
Remix hooks
- Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin.
- Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more.
- Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks.
- Hook radius: 15 mm. Enlarge it for thicker rack rails.
- Pairs well with a mesh laundry bag.
The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Figure8 — Clip-On Cord Winder
Figure8 is a compact cord winder that snaps onto the flex of a kettle, toaster or similar appliance and takes up the slack. Wrap the spare cord around the two end horns in a figure-eight pattern, and the curled horn tips hold the turns in place so the wrapped cord can't spring loose. It is designed for cluttered counters where appliance cords tend to tangle. The spine carries a round channel with a narrower snap-in slot, so the winder stays on the cord instead of sliding off. The cord is pressed through the slot, and the lips flex to let it pass. Dimensions Overall length: 80 mm Overall width: about 46 mm across the horns Height: 9 mm Cord channel: 5 mm diameter, running the full spine Snap-in slot: 4 mm opening Features Four horns with tips curled back toward the centre Chamfered spine edges Single-piece body with no assembly Compatibility Intended for standard 6–7 mm appliance cords, which squeeze through the slot and sit snugly in the channel Print notes PETG or TPU is recommended, since the slot lips need to flex Stiff PLA may crack at the lips when the cord is pushed in Prints flat on the bed; the curled tips are short, so supports are only needed if the slicer flags them
HexGrip — Square-Cut Plywood Hex Clips
HexGrip is a two-clip press-fit system for building hexagonal shelving from 1/2 in plywood, now designed for plain 90° square-cut panel ends. Each slot ends in a solid stop 5 mm from the vertex centre, so neighbouring panels meet at 120° without colliding and no mitre cuts are needed. Features End Cap Clip: two slots at 120° for outer hexagon corners. Spoke Clip: three slots 120° apart for shared vertices in a hexagon network. Barbed slot walls with about 0.55 mm interference per side: ramped entry, steep faces that resist pull-out. Dimensions Slot width 13.0 mm, depth 19 mm Clip height 24 mm, arm length 30 mm Print notes Prints with the slot opening facing up, no supports needed. A single hexagon uses 12 clips, one on the front and one on the back of each vertex. Print one first to check the fit against your actual plywood thickness.
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
120mm Wavy Suspended Planter Pot
A contemporary, self-supporting planter insert designed to seat perfectly into a matching 130mm water reservoir. The exterior features a 12-point wave pattern with a gentle 45-degree sweeping twist, merging seamlessly into a robust 120mm upper resting lip. The interior taper mirrors the outer walls to maintain a reliable 2.5mm thickness, finishing with an elegant inner flare at the rim. Specifications Dimensions: 140mm height, 120mm max outer diameter (at the rim). Clearance: Tapered base drops to ~107mm diameter to comfortably clear standard 130mm reservoir walls. Drainage: Seven 5.5mm functional ports arranged flush to the floor. Printability: The support lip is carried by a calculated 45-degree transition collar, ensuring the overhang prints completely clean without supports. Drops right onto the build plate.
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar