Description
A rigid little handbag that keeps its contents from spilling when tipped. This remix pushes the internal retaining flaps to their absolute limits—stretching them fully into the inner side-walls and shaving them down to a single 0.2mm printable layer, while leaving a secure central gap to retrieve items.
Construction Notes
- Retaining Flaps: Extended to 57mm to anchor directly into the bag's sloping walls, shaved down to 0.2mm thick.
- Heart Motif: Raised 1.5mm off the front face.
- Beaded Handle: Designed to print entirely flat, hooking onto the thin side loops after assembly.
Photos
Technical views
More like this
Explore more in Storage & Organization →
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Support 25 Clés USB
Un support de bureau lourd et stable conçu pour ranger et organiser 25 clés USB en un seul endroit. Variables à ajuster Espacement (28 mm x 23 mm) : Pensé pour accepter la plupart des corps de clés USB sans qu'elles se chevauchent. Peut être resserré si vous n'avez que des clés très fines. Taille des encoches (14 mm x 7,5 mm) : Les fentes offrent un jeu confortable autour d'un connecteur USB-A standard. Profondeur (12 mm) : Laisse les clés bien droites tout en conservant 3 mm de matière pleine au fond du bloc (hauteur totale de 15 mm).
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
C Clip for 9V Battery Container
What it's for A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing. Dimensions Inside pocket: 22 x 33 mm Height: 20 mm Wall thickness: 2.5 mm Opening: 27 mm wide, leaving 3 mm of retaining wall on each side Outside: 38 x 27 mm Remix ideas Widen the opening to 28 or 29 mm for an easier release. Add a mounting tab or screw holes on the back wall. Print in PETG or nylon for better flex at the snap.
Organizador gloss
Organizador de gloss com estética de penteadeira rosa: um bloco baixo com 10 furos em grade 5x2, o nome "Laura" em relevo na frente e dois pequenos corações rosa, um de cada lado do nome. 10 furos de 22 mm de diâmetro Nome e corações em rosa mais forte que o corpo Corações em relevo, sem suportes Fácil de trocar o nome ou a quantidade de corações