10-Inch Kicker Subwoofer Spacer 4800 ribs
Created today
Description
A precise 6mm-thick mounting spacer for a 10-inch Kicker subwoofer, designed to match the 47KBRW10 frame.
Features
- Bolt Pattern: 8 holes starting at the 11:30 position and distributed uniformly clockwise around the 252mm BCD.
- Cable Routing: Four dedicated horizontal underside rib channels.
- Fitment: Engineered with accurate 1-inch offsets for structural routing to avoid pinching or sealing issues along specific axes.
Images
More like this
Explore more in Automotive, RC & Hobby →
Apache 4800 Kicker Sub Spacer
A custom 6mm spacer for mounting a Kicker 10-inch subwoofer frame inside an Apache 4800 hard case. Features specific underside relief channels on the top and bottom edges (holes 1-2 and 5-6) so the case lid ribs can slot directly underneath without interfering with the mounting face. The top surface remains perfectly flat to ensure a flush seal with the speaker basket. Pattern: Standard 8-hole (252mm BCD) Clearance: 3.2mm wide by 3mm deep horizontal channels on Z=0 Thickness: 6mm overall
5/16x14 Cue Joint Protectors
A matched set of joint protectors for pool cues using the 5/16x14 piloted joint standard, heavily used by Schon and similar makers. Includes a female cap to protect the exposed butt pin, and a male plug to seal the shaft insert. Both feature fluted outside edges for easy threading and unthreading. Remix Hooks Cue Diameter: Default is 21.5mm OD. Thicker cues might want 22mm; older cues might sit closer to 21.2mm. Clearance: The female thread (butt protector) is oversized by 0.6mm, and the male pin undersized by 0.2mm to survive FDM printing tolerances. Dial these in depending on your printer's flow rate. Pilot Recess: The butt protector has a 13.5mm diameter x 3.5mm deep recess to clear a standard Schon pilot collar. Grip Profile: The 4mm semi-circle edge flutes can easily be swapped for a knurled mask or flat-cut hex sides.
Motorcycle Numberplate Spray Deflector/Mud Guard
That perfectly aligned stripe of wet road grime the rear tire slings exactly past the bottom edge of the plate and up the center of your jacket is miserable. Tail tidies look good, but they leave the dead center of the wheel completely unshielded. This is a wedge deflector that clips directly onto the bottom edge of the numberplate. It projects a downward-angled, 18mm shelf backwards toward the wheel, catching that specific arc of water and directing it back at the road. The ends are heavily swept to match the sharp lines of modern sport bikes like the Z-series. Fitment & Printing Slot Width: 3.0mm, deep enough (15mm) to swallow standard plates. Features an internal 0.4mm friction ridge to bite onto the plate. (If your plate is very thin stamped metal, add a strip of double-sided tape inside the channel). Deflection Range: 90mm wide to cover the tire's central spray path, with an 18mm rearward overhang. Print Orientation: Drop it flat on its front face in your slicer. The awning prints upwards at an angle, meaning the whole piece prints cleanly with zero supports. Material: PETG or ABS/ASA strongly recommended. PLA will warp from exhaust heat or summer sun.
Kayak Track Anchor Cleat
A heavy-duty zig-zag anchor cleat designed specifically for marine T-track systems (YakAttack, Scotty, RAM). This printed assembly includes the cleat body, two M8 threaded T-bolts, and two knurled hand nuts. Fitment Details Track Slot: The alignment boss on the bottom of the cleat is sized at 8.5mm to drop perfectly into standard 9mm (3/8") kayak track top slots. T-Bolt Heads: The included bolts have 11.5mm x 22mm heads designed to slide through the wider internal channel of the track without pulling through the top. Hardware: The printed hardware uses standard M8x1.25 threads. The heavier 8mm shaft is vastly stronger than 1/4-20 when 3D printed, while still fitting flawlessly through a standard kayak track slot.
Lego piece for wagon door runner with thinner teeth bit
Wagon door runner to replace 3 off 15208 bricks
Terraced House Front with Quoins
Naked corners on a model building always look unfinished and make it impossible to hide the seam when you butt it up against a side wall. I've added alternating quoin stones up both edges that wrap the full thickness of the part to cap it off. Build Details Scale: OO Gauge (4mm to 1ft) Dimensions: 64mm wide × 72mm high × 3mm wall depth. Fit: Quoins extend back to the Z=0 plane and overhang the sides by 0.2mm to overlap any adjacent pieces nicely.