Made by AdeptStork
Created today
Description
A toy dump truck about 113 mm long, built from a frame that carries a cab, a hinged cargo bed with a canopy roof, a tailgate, two swinging doors and four wheels on two axles. The bed pivots on a rear pin so it tips like a dump bed. A tailgate closes the rear of the bed and swings down on a bottom pin, held shut by two turn-button latches. Each door is a separate panel with a front pin, and a blocky figure sits in a cut-out seat well with poseable limb joints. The bed carries a separate one-piece load of crates, barrels, a toolbox and a spare tire, and a canopy roof on four corner posts covers it. Body details include headlights, grille bars, bumpers, tail lights, bed ribs, mirrors, door handles, exhaust stacks, a roof light bar and a steering wheel.
The model is arranged as a flat print layout: frame, cab, cargo bed, roof, load, tailgate, latches, doors, figure, wheels and axles sit apart on the plate, then assemble into the truck. The layout is about 192 × 235 mm and fits 256 mm Bambu Lab beds; it does not fit an A1 mini.
Images
A 1/10-scale ladder-frame chassis for a rear-wheel-drive RC hot rod truck. The frame is 340 mm long with 95 mm rail spacing and a 260 mm wheelbase, and it includes a front servo plate, motor plate, battery tray with cutouts, rear diff block, six body-mount posts, and placeholder axles and wheels. The dimensions are a starting point rather than a scale copy of a full-size Factory Five 1935 truck, and the mounts and axles are not sized to a specific motor, diff, servo, battery or drivetrain. Check hardware fit before printing. The frame length exceeds many printer beds, so plan for a large-format printer or split the frame into sections. Frame: 340 mm long, 95 mm rail spacing, 260 mm wheelbase Includes: five crossmembers, front servo plate, motor plate, battery tray with cutouts, rear diff block, six body-mount posts Placeholder parts: axles and wheels, not matched to a specific drivetrain Printing note: 340 mm frame length may require a large bed or sectional printing

A sleeve that drops into an oversized cup holder and shrinks it, so a slim energy can sits snugly instead of rattling around. Three angled flex fins on the outside wedge the sleeve into holders of different widths. What it's for Sizing down a large truck cup holder for a slim energy can or a standard 500 ml can. Holding the can upright without side-to-side movement. Fitting holders from roughly 80 mm to 95 mm across, using the three flexible fins on the outside. Dimensions Height: 70 mm Body outer diameter: 76 mm Inner bore for the can: 66 mm Base well: 70 mm diameter, 4 mm deep, for the can's bottom rim Drain hole in the base: 20 mm Fins: 3, spaced 120° apart, spanning about 80–95 mm overall, positioned between 14 mm and 56 mm up the body Top edge: small flared lead-in for easy can insertion Print notes PETG works for the whole part. TPU for the fins gives more flex without cracking. Print upright with the base on the bed. No supports are needed for the body. The fins are thin blades, so they bend inward when pushed into a holder. A snug can may need a little extra bore clearance. Fit has not been tested in a real holder, so check your holder's diameter first. Remix ideas Change the bore diameter for other cans or bottles. Add more fins or make them thicker for a firmer grip. Shorten the body for a low-profile holder. Increase the drain hole or add slots to let water escape.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.
Straight and curved RC track pieces sized to fit a 250 x 250 mm print bed, using the same 90 mm wide track and bulb-and-socket latch as the rest of the set. What it fits Built for printers with a 250 x 250 mm bed or larger. Mates with the existing 90 mm wide pieces (80 mm clear lane, 5 mm rails) through the same latch with 1 mm clearance. Pieces Straights: 50 mm and 150 mm (the 200 mm straight also fits). 180° hairpin at 70 mm centreline radius, about 230 mm wide. 30° at 250 mm radius, 45° at 200 mm, 60° at 150 mm, 90° at 120 mm. Check before printing The footprint of each piece is measured from the model, but measure your bed's usable area, since brims and clips reduce it. Does not fit The earlier 180° hairpin at 100 mm radius, the main junction (about 440 mm) and the multi-way junctions are larger than a 250 mm bed. The latches have not been test-fitted.
608 rulman yuvalı, M3 cıvata ve somunla kapanan iki yarım gövdeli, 2 vitesli kayar dişli şanzıman. Giriş milinde 12T ve 24T sabit dişliler, çıkışta 36T+24T kayar dişli kümesi bulunur; 1. vites 3:1, 2. vites 1:1 ve iki çiftte de eksenler arası mesafe 36 mm'dir. Altı parça ayrı basılır ve montaj ister: alt gövde, üst kapak, giriş mili, D profilli çıkış mili, kayar dişli kümesi ve vites kolu. Üst kapağın dış yüzeyinde, kapanmış halde kullanıcıya bakan tarafta 0,8 mm derinliğinde oyulmuş "benze" yazısı vardır. Kapak ters basıldığı için yazı tablaya oturmaz. Gövde iç duvarları hızlı baskı için 1,6 mm'ye inceltilmiştir; rulman yuvaları, cıvata kulakları ve mil uçlarının duvarları 2,4 mm'de kalır. Uyumluluk 608 rulman: 8 mm iç çap, dört adet. Rulman kullanılmazsa basılı kaymalı burç seçeneği vardır. M3 cıvata: yaklaşık 12–16 mm, altı adet; M3 somun altı adet. Mil uçları: giriş ve çıkışta 5 mm D profil veya 5 mm D delik. Dişli standardı: modül 1.5, 20° basınç açısı, düz dişli. Baskı öncesi kontrol Alt gövde ve üst kapak, baskı yerleşiminde yaklaşık 92 × 93 mm taban alanı kaplar; tabla en az bu ölçüyü almalıdır. 608 rulman yuvası 8 mm iç çapa göre çıkar. Rulman yerine basılı burç kullanılacaksa mil çapı aynı ölçüde tutulmalıdır. Gövde iç uzunluğu üç dişli konumu ve kayma payı nedeniyle yaklaşık 60 mm'dir; 36T dişli yüksekliği belirler. Uymadıkları 90 × 50 × 45 mm gövde ölçüsüne sığmaz. Gerçek dış ölçü yaklaşık 92 × 93 × 32 mm'dir. Tek kayar dişliyle 3:1 ve 1:1 aynı eksen mesafesinde elde edilemez; bu modelde kayar küme 24T+36T çift dişlidir. Hazır bir redüktörün yerine doğrudan geçmez; miller, dişliler ve gövde birlikte basılan bağımsız bir düzenektir. Destek malzemesi gerektirmeyecek şekilde düz yüzeyler tablaya gelecek biçimde yerleştirilmiştir. PLA veya PETG ile 0,2 mm katman yüksekliğinde basılabilir; dişliler ve miller için %40–60 dolgu, gövde için %20–30 dolgu yeterlidir.