2 cadenas module
Created 1 months ago
Description
A wall-mounted 200×200 mm lockout tagout station designed to hold 15 industrial safety padlocks. The single-piece board features reinforced, support-free pegs sized to slip through standard 6.35 mm padlock shackles, retaining them securely while lying completely flat on the print bed.
- Dimensions: 200 mm width × 200 mm height × 12 mm total depth
- Capacity: 15 padlocks (3 rows of 5)
- Hook Profile: 5 mm diameter shaft, expanding to a 7 mm chamfered retaining lip
- Material Guidelines: Optimized for PETG; standard print cooling recommended for the peg tips
- Mounting: Four 5 mm countersunk wall-mounting holes
Images
More like this
Explore more in Workshop & Tools →
Elliptical Pedal Insert 48x40 Offset Hole
What it's for Central reinforcement insert for an elliptical trainer pedal, bonded into the damaged opening. Flat top, ribbed underside. Dimensions Base: 48 × 40 × 7 mm, rounded corners Through-hole: 10 mm, centered at 24 mm along the length and 4 mm toward the top edge from the width center 18 mm boss around the hole, 5 ribs to a 3 mm frame Remix ideas Change the hole offset for a different pedal Add or remove ribs Thicken the frame for heavier loads
final cable lock sideways servo
Servo-operated cable lock for a paddleboard rental system, laid out as five separate printed parts: housing, service cover, release slide, cable unit and servo arm. The release slide prints top face down, so the yoke arm forms the first layers and needs no supports. The cable unit lies with its round head on the bed. Printer: Bambu Lab A1 mini, PETG or ASA Cable unit: 4 mm rod with 10 mm round terminal head and a magnet pocket in the tip Slide: 7 mm locking slot, 14 mm release hole, 9 mm travel Servo: 9 g micro servo, lead exits at the front end Export: set part to housing, cover, slide, cable or arm Untested: the design has not been load-tested and is not waterproof
French Cleat Pliers and Drill Holders
A pair of tool holders that hang on a 45° french cleat wall: a pliers rack and a cordless drill holder. Each has a matching 45° lip on the back, sized for an 18 mm ply cleat with 0.5 mm of clearance, so it drops on and stays put under its own weight. Built for a bare garage wall where the tools currently live in a bucket. Pliers holder: 90 mm wide, 95 mm tall, with a 10 mm shelf that projects 45 mm. Two handle slots sit at 25 mm and 65 mm across and taper slightly open toward the back. Drill holder: 130 mm wide, 105 mm tall, with a 10 mm shelf that projects 85 mm. A 40 mm round chuck opening is open to the front, and four 9 mm bit holes sit near the side edges. Remix hooks Cleat size: the cleat thickness (18 mm) and clearance (0.5 mm) drive the lip. Change them to match 12 mm or 19 mm stock. Tighten the clearance only after a test print. Slot count and spacing: add more pliers slots by widening the holder and repeating the slot positions. Narrow or widen each slot to suit your handle thickness. Chuck opening: the 40 mm diameter suits a typical cordless drill chuck. Adjust it for larger drivers or impact guns. Drill extras: the bit holes are 9 mm. Resize them for hex bits or drill bits, or replace them with a battery cradle. Shelf strength: the shelf is 10 mm thick with 4 mm gussets. Thicken it for heavier tools. Pairs well with More cleat-mounted holders cut to the same lip profile. A length of 45° ply cleat screwed into studs, with the holders spaced about 20 mm apart (the pliers holder is 90 mm wide and the drill holder is 130 mm wide). Print each holder on its back, and test the cleat fit on a short piece before committing to a full print.
Tapa cuadrada con agujeros mixtos
Tapa de 180×180×5 mm con dos lados redondeados a la izquierda (radio 10 mm), cuatro agujeros M3 en las esquinas y un agujero de 5 mm. Dos agujeros redondos de 35 mm a la derecha y cuatro cuadrados de 36 mm a la izquierda, en la zona inferior. Ideas para remezclar Diámetro de los redondos (35 mm): súbelo o bájalo según la pieza que deba pasar; la pared entre ellos es de 7 mm. Lado cuadrado (36 mm): ajústalo por separado; los centros están a 42 mm. Radio de las esquinas (10 mm): 5 mm para una curva más suave. Agujero de 5 mm: está a 25,5 mm sobre el centro; muévelo para un pasacables o un pulsador. Combina con: una base o caja de 180 mm usando los M3 de las esquinas (3,4 mm, a 8 mm del borde).
SpoolScope — Filament Remaining Gauge
SpoolScope is a two-part gauge for estimating how much filament remains on a standard spool, made for spools that sit out of easy view in an AMS or on a shelf. The rail hooks over the flange rim; the sliding block rides on it with light detents, so you can push it down until it touches the filament, lift the gauge away and read the result. Raised ticks and numbers plus an unambiguous arrow on the block make the measurement clear without needing line-of-sight while the gauge is in place. Features Two printed parts: a rail with a rim hook, and a detented sliding block. Gram scale from 0 to 1000 g, with ticks every 50 g and numbers every 100 g. Ticks follow filament geometry rather than an even spacing: closer together near full, wider apart near empty. Arrows on the block tip directly toward the scale, and the detents hold the reading after the gauge is lifted off. Hook gap of 4 mm, sized to clear flanges from 2.8 mm to 3.6 mm thick. Dimensions Flange diameter: 200 mm. Hub outer diameter: 95 mm (from a measured Polymaker spool). Full-roll diameter: 170 mm (estimated from a 1 kg PLA roll on a 95 mm hub and a 65.6 mm spool width). Hook gap: 4 mm. Fitting and calibration Sized around Polymaker and Inland 1 kg spools; other brands are worth checking against the hub and flange figures above. The scale can be shifted by a single fixed offset if a first print reads consistently high or low, so a weight check against a known spool is worth doing before trusting the numbers. If the error differs between a full and an empty spool, the hub and full-roll values are the ones to correct. Print notes Both parts are laid out flat on the print plate. The block contacts the filament at its outer edges rather than at the centre, so a reading can sit slightly high; a weight check against a known spool is the best way to confirm the scale.
Support mural tournevis 255 × 40 × 40 mm
Support mural pour tournevis : plaque verticale de 255 × 40 mm et tablette horizontale de 255 × 40 mm, épaisseur 5 mm. Trous de la tablette, de gauche à droite : 10, 10, 10, 7, 7, 7, 7 mm, bords arrondis. Deux trous de vis fraisés dans la plaque. Texte « TOURNEVIS » en relief de 1,5 mm. Coins extérieurs arrondis à 10 mm ; les deux coins à la jonction plaque/tablette sont droits. À vérifier avant impression : la longueur de 255 mm doit tenir sur votre plateau. Ne convient pas aux tournevis dont la tige dépasse 10 mm.