110mm Hex-Mesh Planter Pot
Created 1 months ago
Remixed once
Description
A tapered cover pot designed for standard 12cm nursery planters. The base and walls feature a staggered hexagonal mesh that promotes extensive airflow and rapid drainage.
- Dimensions: 150mm outer top diameter, 140mm inner top, tapering to fit a 120mm base. Total height is 120mm.
- Printability: The wall hexagons are rotated so their corners point straight up, yielding sharp 60-degree overhangs that print perfectly without supports.
- Durability: Uniform 5mm walls provide rigidity even with the extensive mesh cutouts.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
120mm Wavy Suspended Planter Pot
A contemporary, self-supporting planter insert designed to seat perfectly into a matching 130mm water reservoir. The exterior features a 12-point wave pattern with a gentle 45-degree sweeping twist, merging seamlessly into a robust 120mm upper resting lip. The interior taper mirrors the outer walls to maintain a reliable 2.5mm thickness, finishing with an elegant inner flare at the rim. Specifications Dimensions: 140mm height, 120mm max outer diameter (at the rim). Clearance: Tapered base drops to ~107mm diameter to comfortably clear standard 130mm reservoir walls. Drainage: Seven 5.5mm functional ports arranged flush to the floor. Printability: The support lip is carried by a calculated 45-degree transition collar, ensuring the overhang prints completely clean without supports. Drops right onto the build plate.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
горшок илья
A solid-walled, 140mm tall flower pot with subtle vertical waves along its tapered exterior. The base tapers from a 120mm top opening down to 105mm at the bottom, featuring a robust 4mm thick floor and exactly eight 6mm drainage holes to keep soil adequately drained. Remix Hooks Wall Thickness: Currently 3mm, cleanly subtracted from the inner radius so the exterior waves never break through. Wave Amplitude: Set to 1.5mm with 24 peaks around the perimeter; you can scale the amplitude up for a deeper scallop or increase the frequency for a ribbed texture. Drainage Pattern: The 8 holes sit on a 60% radius ring; this is an easy block to swap out if you prefer a slotted grid or a single large center hole. Scale Factor: The linear extrusion uses a calculated 120/105 ratio. Tweaking this lets you flare the pot wider or pull it into a straight cylinder.
Botanical Propagation Tray
A shallow, rectangular nursery tray built specifically for sowing seeds and propagating small cuttings. It is elevated on four short feet to allow excess water to escape underneath, preventing root rot. Design Features Drainage Grid: A regular pattern of 3.5mm holes across the bottom ensures proper water flow. Elevated Base: 5mm feet keep the tray off flat surfaces, allowing air circulation and drainage. Sturdy Walls: 2mm thick perimeter walls provide enough rigidity to move the tray when fully loaded with damp soil.
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
Twisted Planter With Name Plaque
A 100mm base hexagonal planter with a deep twist and a prominent front plaque. The planter features a solid 5mm-thick wall that precisely tracks the exterior twist, terminating in a flared rim. It includes a central 8mm drainage hole alongside five 10mm perimeter holes. A pill-shaped plaque sits seamlessly flush on the front face, equipped with extruded placeholder text ("NAME") that will export as part of the geometry—ideal for setting up multicolour text in your slicer. Check your drip tray to ensure the 100mm base clears the lip.