150mm Tapered Hair Tie Stand
Created 5 months ago
Description
A vertical storage post designed to hold hair ties, featuring a tapered central shaft and an expanded base to prevent toppling during use. The conical geometry allows varied sizes of elastic bands to settle naturally along the shaft according to their diameter.
Specifications:
- Vertical Height: 150mm tapered shaft section.
- Taper Dimensions: 50mm diameter at the base terminating in a 25mm diameter at the top.
- Base Design: Thickened, extended base footprint for structural stability.
- Application: Storage and sorting of hair ties, allowing immediate access and gravity-assisted sizing.
Images
More like this
Explore more in Kitchen & Bathroom →
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Vented Snap-On Toothbrush Cover
A slide-on travel cover designed to enclose the head of a standard adult toothbrush. Protects bristles from crushing and external contact during transit, while the top-face perforations allow airflow so the brush can dry between uses. The base incorporates side-relief slits and internal retention bumps to snap securely over the neck of the brush, holding the cover in place in a travel bag. Interior cavity measures 26 mm wide, 16 mm deep, and 33 mm tall Vented top allows passive moisture escape Flex-slit base expands to accommodate varying handle tapers Snap-fit retention bumps grip the brush neck
Slanted 6-Slot Knife Block
A countertop block designed to hold six standard kitchen knives. The body and interior slots lean backward at a 15-degree angle, presenting the handles for quick identification and unobstructed access while cooking. Six individual slots measuring 4 mm by 30 mm. Open-bottom cutouts prevent moisture accumulation inside the block. Flat, stable base for solid countertop placement.
Cucharilla de dos piezas con conector
What it's for Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas. Dimensions Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor. Alojamiento: 16 × 6 mm, 23 mm de profundidad. Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic. Ventanas laterales de 4 mm donde se aloja el resalte. Remix ideas Añadir una cabeza de cuchara en la pestaña tope del conector. Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme. Cambiar el radio de curvatura del mango.
Mango recto con soporte giratorio
Mango recto con soporte giratorio para cuchara, de 12 cm de largo total, 2,8 cm de ancho y 1,6 cm de alto. Se compone de dos piezas independientes unidas por un tornillo M4 vertical y una tuerca hexagonal en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Largo total: 12 cm Mango: unos 9,4 cm, se afina hacia el extremo Lengüeta de 4 mm con disco de 20 mm y orificio de 4,6 mm Soporte con ranura de 4,4 mm y alojamiento para cabeza de tornillo y tuerca M4 Tornillo y tuerca no incluidos