32mm to 25mm Vacuum Adapter
Created 3 months ago
Description
A straight adapter designed to connect a 32mm shop vacuum hose to a 25mm power tool dust port. The exterior features raised retention ribs, ensuring a standard hose clamp can grip the adapter securely without slipping under tension or vibration.
The geometry incorporates precise dimensional offsets to allow for an immediate friction fit:
- 31.5mm outer diameter on the vacuum side to slip inside a standard 32mm hose.
- 25.5mm inner diameter on the tool side to slide smoothly over a 25mm tool port.
- Raised exterior ridges running along the body for improved hose clamp retention.
Images
More like this
Explore more in Workshop & Tools →
Machined-Style NPT Blow Gun Nozzle v4
An air compressor adapter designed to interface a 1/4" NPT blow gun with a precise 3mm outer-diameter nozzle. The part features a clean, support-free geometry that steps inward as it prints, transitioning smoothly from a 14mm hex base up through the threads, capping off with a reinforced 1mm fillet at the base of the delicate tip. Print and Application Notes Print Orientation: Prints exactly as oriented (hex base flat on the bed). No supports are required for the threads, ceiling, or nozzle. Sealing: The threads are rendered straight rather than tapered—wrap with a couple of layers of PTFE thread tape to ensure a tight pneumatic seal when threading into the metal gun. Material: PETG or ABS is highly recommended over PLA to handle the pressure spikes and avoid brittleness at the tiny 1mm bore tip.
1/4" NPT Golf Grip Air Adapter v2
Adapter to mate a 1/4" NPT air compressor blow gun directly to a golf club grip vent hole. Uses a 16mm hex drive for tightening. Fitment Notes Mating Surface: 1/4" NPT female blow gun ports. The model uses a straight 18 TPI thread (13.5mm OD) that relies on Teflon tape to seal against the tapered female bore. Output: 3mm OD nipple, 4mm long. Backed by a 3mm conical shoulder to prevent snapping under pressure. Bore: 1mm continuous air channel. Check this after printing — a 1mm FDM hole will likely need clearing with a wire or a 1mm drill bit before it flows air properly.
Threaded Irrigation Hose Adapter
What it's for A female-to-female adapter designed to link a stackable irrigation pipe to a standard garden hose. One side features a standard 3/4"-11.5 GHT garden hose thread, while the other side is threaded to screw directly onto the pipe's male fitting. Dimensions Overall length: 38 mm Hex body: 42 mm (circumscribed) for easy hand or wrench tightening Bore: 19 mm straight through to match the pipe's internal diameter and eliminate flow restriction Design notes The internal bore transitions smoothly into flat seats on both ends, allowing standard hose washers or O-rings to seal perfectly against the fitting. The thick hexagonal walls withstand outdoor water pressure without flexing.
Knurled Tripod Thread Adapter
A threaded step adapter for mounting 3/8-16 photography and audio equipment to standard 1/4-20 tripod studs. The flanged base features a deeply scalloped outer diameter to allow firm, tool-free tightening. Specifications: Base Thread: 1/4-20 UNC (female) Top Thread: 3/8-16 UNC (male) Grip Style: Scalloped profile Tolerances: Thread profiles offset for FDM printability
Detailer's Triptych Vacuum Set
A custom trio of detailing tools designed specifically for the standard 35mm friction-fit wands found on most Karcher wet/dry workshop vacuums. Each piece serves a distinct stage of an automotive deep clean. The set features: The Crevice Tool (Red): Extended and sharply angled to slip between seats and center consoles. The Wide Nozzle (Blue): Flared to 80mm with a shallow scraping edge, ideal for lifting stubborn dirt from floor mats and broad upholstery. The Detailing Spot Nozzle (Green): Narrowly focused into a 16mm tip for intense, localized suction inside cup holders, vents, and door pockets. Designed to print without supports—just drop them on the bed vertically.
Packout M18 Router Insert
What it's for A custom drop-in tray engineered to convert a half-section of a Standard Milwaukee Packout Organizer into a dedicated M18 router station. It features a contoured cradle for the router body with its battery attached, a wide pocket for the base plate, a large accessory bay for the edge guide and wrench, and a 12-slot storage grid for 1/4-inch shank router bits. Scalloped finger pulls make it easy to lift the router out. Dimensions Footprint: 280 mm × 200 mm Height: 60 mm Bit Storage: 12 holes, 7.2 mm diameter (for easy clearance of standard 1/4" shanks) Print notes Given the large 280 mm length, this will require a reasonably large print bed. A robust infill (15–20% gyroid) is recommended to support the weight of the tool. The design rests entirely flat on the build plate and requires no supports.