3D Cube IQ Puzzle
Created today
Description
A miniature, low-filament version of the classic Soma cube puzzle.
The set includes seven distinct pieces that assemble into a solid 3x3x3 cube. The puzzle comes with a small square container to store the pieces or to build the solution directly inside.
Print Details
- Pieces: 7 standard Soma cube fragments
- Container: 33.5mm outer footprint
- Supports: None required. All puzzle pieces are oriented to print flat against the build plate.
- Solvability: Mathematically proven to have exactly 240 valid solutions.
Images
More like this
Explore more in Storage & Organization →
4-Compartment Kitchen Organizer
A small, straightforward drawer organizer divided into four compartments. One wide compartment runs the length of the tray for standard utensils, while the back half is split into three smaller bays for loose items. Dimensions Overall size: 150 mm long × 100 mm wide × 35 mm tall Wall thickness: 2 mm solid walls and dividers Long bay: ~146 mm × 47 mm (ideal for small spoons or forks) Small bays: ~47 mm × 47 mm each Print notes Designed to print flat on its base without supports. Generous corner radii keep things from getting stuck in the corners. PLA or PETG both work fine for drawer use.
130mm Tubeless Repair Kit Case
A rigid three-piece storage case designed for tubeless tyre repair kits. The base features an inset lip that locks the lid in place, secured by a snap-fit C-clamp latch that mounts to an integrated front axle. Dimensions: 130 mm x 85 mm x 35 mm combined. Wall Thickness: 2.5 mm throughout. Clearances: 0.3 mm on the lid slip-fit, 0.5 mm width clearance for the latch. Print Orientation: All three pieces are laid flat on the bed. No supports required.
Cascading Hex Organizer
A minimalist, honeycomb-inspired desk organizer that steps up in height to hold everything from SD cards to tall pens. Its stepped layout is optimized for rapid support-free 3D printing. Zero Supports Required: Designed to print flat on the bed with no overhangs. V-Groove Details: Chamfered edges create a premium architectural look where the cells meet. Stepped Heights: Makes smaller items just as easy to grab as tall ones.
Ühe Otsaga Suletud Sahtlikarp
Sahtel kiilub kinni, sest pole kuskilt korralikult kinni võtta. See on suletud tagaseinaga lihtne kest, millel on nüüd sahtli ees korralik väike näpu-kõrgendus, et seda saaks mugavalt ja ilma küüsi murdmata välja tõmmata. Mahutavus: Täpselt 200 × 50 × 50 mm kasulikku ruumi. Seinad: 1.5 mm, prinditav ilma tugedeta. Liikumisruum: 0.5 mm lõtk külgedel tagab sujuva liugumise.
VoltGrid — Print-in-Place Battery Case
A high-capacity, print-in-place storage case holding 104 AA batteries in a skeletal, material-saving grid. Designed specifically for FDM printing without supports. Features Zero Assembly: Prints flat with a fully integrated, captive 45-degree cone hinge mechanism. Just pop it off the bed and fold it closed. Skeletal Organizer: The lower grid provides 0.4 mm of clearance for 14.5 mm diameter AA batteries, but uses open walls to drastically cut filament usage and print time compared to solid block designs. Snap Latch: A flexible cantilever tab locks the lid securely down over a heavy chamfered ledge on the bottom box. Dimensions Flat Printing Footprint: 228 mm × 292 mm Closed Dimensions: 228 mm (W) × 142 mm (D) × 60 mm (H) Capacity: 104 cells (13 × 8 grid)
Side-Pinned 40-Quarter Dispenser
A gravity-fed mechanical magazine for standard U.S. quarters. The vertical tube stores up to 36 coins, while a sliding escapement mechanism stages and drops exactly four quarters ($1) per full pull. Design and Fitment Capacity: 40 quarters maximum (36 in the tube, 4 seated in the slider). Clearances: The magazine bore is 25.2 mm (oversized from the 24.26 mm quarter) to prevent binding, with a 28.8 mm x 7.6 mm slider track for horizontal travel. Structural Details: The base of the primary magazine tube features a 4 mm flared buttress, preventing shear failure across the layer lines when fully loaded. Hardware: Fully printed, no external fasteners or springs required. The side-mounted 4.0 mm stopper pin captures the slider in the track and sets the 26 mm travel limit.