40mm Stud Mount Coat Hook
Created 1 months ago
Description
A robust coat hook designed for direct anchoring into a standard wooden wall stud. The angled peg provides substantial clearance for heavy fabrics, while the backplate keeps the mounting hardware strictly inline for reliable engagement with a single structural member.
Fitment & Installation:
- Mounting Interface: Two countersunk mounting holes spaced exactly 40mm apart on the vertical axis.
- Fastener Compatibility: Sized to accept standard #8 wood or drywall screws. The countersink depth ensures the screw heads seat entirely flush beneath the surface, preventing snags on coat collars.
- Clearance: The lower hook geometry is offset to allow straight-line access for a standard driver bit during installation.
Images
More like this
Explore more in Home & Fixtures →
Scandi Flared Coat Hook
What it's for A minimalist, Scandinavian-inspired wall hook for coats, bags, or towels. The flared cap prevents items from slipping off while maintaining a soft, continuous profile. It mounts using a single countersunk screw through the center, with a deep counterbore that allows the screw head to sit well below the surface—ready to be left exposed or covered with a standard 9.5mm wooden plug. Dimensions Length: 63 mm from the wall. Diameters: 22 mm at the wall base, tapering to 16 mm at the neck, and flaring to a 38 mm cap. Hardware: 5 mm through-hole with a 9.5 mm counterbore (suits a standard #8 or #10 wood screw). Print notes The flare angle is kept under 45 degrees, meaning this prints cleanly standing straight up on its base without any supports. If you want a smoother finish on the front face, you can flip it 180 degrees in your slicer and print it face-down (the chamfers and rounding will print perfectly either way).
Flat-Backed Angled Wall Hook
A 3D-printable wall hook featuring a straight outer spine for a clean visual line against the wall, paired with a curved inner profile that creates a natural resting notch. Straight spine: Sits perfectly parallel to the mounting plate. Inward curve: Adds depth to the hook's catch without thinning the whole shaft. Base plate: 30x30 mm, sized for standard mounting tape.
Appendiabiti a Traliccio 32mm
Appendiabiti rigido a parete stampabile in 3D. Disegnato con un profilo sagomato per ridurre il consumo di filamento mantenendo un'elevata resistenza al carico. Interasse: 32 mm esatti. Fori: 3,2 mm (per viti da 3 mm), con svasature da 4,5 mm posizionate a profondità fissa. Accessibilità: tunnel orizzontali da 8,5 mm per inserire agilmente vite e cacciavite. Orientamento: Da stampare rigorosamente coricato sul fianco per sfruttare la direzione dei layer.
9-Inch Planter Drainage Raiser
A structural insert built to elevate a 9-inch plastic nursery pot inside a decorative ceramic planter. Standing 3 inches tall, it provides a solid base while allowing standing water to drain clear of the roots. The top deck uses a concentric ring and spoke pattern — significantly stronger and faster to lay down than a square grid. The load is carried outward to four tapered pillars set directly under the main intersections. Remix Hooks Total Height: Built at 76.2 mm (3 inches), but the leg pillars can be stretched or squished to match any outer pot depth. Deck Thickness: Starts at 6 mm to handle a 20 lb load without bowing. Leg Taper: Set at 24 mm at the base narrowing to 18 mm at the top — widen the base if you need it to sit on a softer medium instead of a hard ceramic bottom.
Pendant Canopy With 50mm Mount
Electrical brackets that don't line up with standard covers leave you with a gaping hole in the ceiling and wires hanging out. This ceiling canopy replaces the usual single-point hook system with a direct two-screw mount spaced exactly 50mm apart to mate perfectly with standard central hub brackets. Canopy Diameter: 105mm to comfortably bridge rough plaster holes. Mounting Holes: Spaced at exactly 50mm center-to-center with 5mm clearance for standard bracket screws. Core Pass-through: 8mm internal channel easily clears standard twin-core lighting cable.
