45mm Diamond Leaf Napkin Ring
Created 1 months ago
Description
A dual-purpose cylindrical sleeve functioning as a napkin ring and tealight surround. The 5mm wall provides structural rigidity and blocks stray light, while a staggered array of diamond-shaped leaf cutouts allows for a crisp lattice pattern when illuminated from within. Sized to accommodate a standard rolled cloth napkin.
- Inner Diameter: 45mm
- Outer Diameter: 55mm
- Overall Height: 40mm
- Wall Thickness: 5mm
- Pattern Type: Staggered diamond lattice
- Use Case: Napkin holding or tealight illumination
Photos
Technical views
More like this
Explore more in Kitchen & Bathroom →
Cucharilla de dos piezas con conector
What it's for Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas. Dimensions Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor. Alojamiento: 16 × 6 mm, 23 mm de profundidad. Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic. Ventanas laterales de 4 mm donde se aloja el resalte. Remix ideas Añadir una cabeza de cuchara en la pestaña tope del conector. Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme. Cambiar el radio de curvatura del mango.
Mango recto con soporte giratorio
Mango recto con soporte giratorio para cuchara, de 12 cm de largo total, 2,8 cm de ancho y 1,6 cm de alto. Se compone de dos piezas independientes unidas por un tornillo M4 vertical y una tuerca hexagonal en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Largo total: 12 cm Mango: unos 9,4 cm, se afina hacia el extremo Lengüeta de 4 mm con disco de 20 mm y orificio de 4,6 mm Soporte con ranura de 4,4 mm y alojamiento para cabeza de tornillo y tuerca M4 Tornillo y tuerca no incluidos
Mango curvo con soporte de cuchara giratorio
Conjunto de dos piezas independientes: un mango curvo de 120 mm y un soporte de cuchara que se encaja sobre su extremo. La unión se hace con un tornillo M4 vertical, introducido desde arriba, y una tuerca en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Especificaciones Mango: 120 mm de largo, 25 mm en la base, 20 mm en el extremo, 16 mm de grosor. Lengüeta del mango: 4 mm de grosor, disco de 20 mm, orificio de 4,6 mm. Soporte: ranura de 4,4 mm, orificio pasante de 4,6 mm. Cabeza del tornillo alojada arriba; tuerca M4 hexagonal alojada abajo. Alojamiento de la cuchara: 14 × 5 mm. Tornillo y tuerca M4 no incluidos.
Smart tap attachment
Assembled touchless tap attachment: a 110 × 80 × 60 mm ABS enclosure with every internal component mounted in place, plus a specification plaque in front. What it mates with Tap adapter for 15–24 mm taps, with a 20 mm ID / 28 mm OD / 3 mm silicone O-ring beneath it 6 mm OD / 4 mm ID PU tubing to 1/4" (6 mm) quick-connect fittings and a 12 V NC solenoid valve E18-D80NK IR sensor through an 18.5 mm bore in the front wall Inside the enclosure 50 × 40 mm control PCB and 35 × 25 mm SPET driver on standoffs with M3 screws 35 × 25 mm relay module and a 12 V power supply block Red wiring harness between boards, sensor, solenoid and power supply Floor tube clip and four lid screw bosses (M3 × 10 mm) Check before printing The lid sits beside the enclosure so the interior stays visible. The power supply is a 30 × 40 × 22 mm representative block, since no size was specified, so check it against your actual unit. The sensor bore suits an 18 mm body only. Other enclosure sizes are not covered.
lid 2
A round plug-style lid for a container with a roughly 94 mm inside diameter. A 100 mm flange rests on the rim and an 8 mm deep, 93.4 mm plug drops into the bore. Fitment Fits: round containers with a bore near 94 mm. Does not fit: bores under 93.4 mm, or slip-over use on a rim. Measure before printing: the container's inside diameter. The plug is 93.4 mm, so a 94 mm bore leaves 0.3 mm per side. Details: the underside is hollowed to 87 mm, leaving a 3 mm flange top and a 3.2 mm plug wall. Overall height: 11 mm.
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.