4mm Slider Snap-On Zipper Pull
Created 1 months ago
Description
Snap-on replacement zipper pull for jackets and bags. Mates directly with the host slider loop via a flared 1.2mm installation slit, requiring no disassembly of the zipper carriage or sewing. The teardrop body features transverse ribbing designed for positive engagement with heavy winter gloves.
Fitment and Installation
- Host fitment: Standard zipper sliders with wire loops up to 4mm in overall diameter.
- Installation: Press-fit directly over the slider loop. The flared entry guides the wire through the 1.2mm slit into the main bore.
- Critical measurement: Verify the wire thickness of the host slider. A loop wire thicker than 2mm may require excessive force to pass the entry slit and could stress the plastic.
- Incompatibilities: Not suitable for solid-cast zipper bodies with small enclosed holes; requires a standard wire loop to snap over.
Images
More like this
Explore more in Keychains & EDC →
4mm Bore Keychain Table
A miniature four-legged table scaled down for pocket carry. It features a standard rectangular top and four corner legs, with an integrated mounting tab extending from the short edge. Fitment and Dimensions Keyring Bore: 4mm diameter hole, fits standard split rings and mini carabiners. Overall Size: 43mm long (including the tab), 25mm wide, and 18mm tall. Clearance: Prints as a single solid piece; no assembly required.
Micro Print-in-Place Joystick
This is a print-in-place ball joint that acts as a miniature thumb joystick. The entire assembly prints as one welded-together block with an internal 0.4 mm gap; once it's off the build plate, a firm snap frees the stick to rotate and swivel in the base. It is designed to be as small as FDM printers can reliably manage without snapping the stalk.
Stacked Name Keychain Pendant
A black keychain pendant with bold white stacked lettering reading Nodi / Mani / Yani and a small red heart beside the last line. The loop sits above the N. Remix hooks Loop position: centred at about X 2, Y 33 with a 9 mm outer and 4.5 mm hole. Shift it or enlarge the outer diameter for a stronger ring. Heart gap: the heart sits about 1 mm clear of the final letter. Change its X offset (34.2) to adjust spacing. Layer heights: 3 mm black base, 2 mm raised white lettering and red heart, 5 mm total. Font: Archivo Black at 8.5 mm; swap for a rounder face for a softer look. Pairs with: a split ring or small carabiner; assign black, white and red to separate AMS filaments.
LANA Heart AHMED Keychain Nameplate
A three-colour keychain nameplate reading LANA ♥ AHMED, about 60 × 10 mm and 5 mm thick: a 3 mm black base with white letters and a red heart raised 2 mm on top. A black loop on the left end has a 4.5 mm through-hole for a standard key ring. Remix hooks Base thickness (3 mm): the number that sets the plate's heft. Drop it for a lighter tag. Raised height (2 mm): letters and heart share it. Make the heart taller for emphasis. Loop hole (4.5 mm): widen it for thicker rings or cord. Backing margin (1.5 mm): the black border around the letters. Thicken it for a sturdier outline. Names and font: the text is DM Serif Display at about 7 mm tall. Swap the names or the typeface. Pairs well with a metal split ring. Each colour is a separate region for AMS assignment.
Chubby Sitting Hamster Keychain
A compact, sitting hamster figure modelled with exaggerated, rounded proportions for a chunky silhouette. The base is sheared flat to allow support-free printing directly on the build plate, and a reinforced loop is integrated into the upper back of the head. Dimensions: ~28mm wide, 30mm tall. Keyring Loop: 3.2mm horizontal bore, heavily chamfered outer ring. Print Settings: Print upright. The limbs and facial features intersect closely with the main body to minimise overhangs; no supports are required.
Chaîne articulée de 40 maillons clipsables
Une chaîne imprimée d'un bloc se désassemble au moindre effort, et une chaîne trop courte ne sert à rien. Cette version aligne 40 petits maillons à rotule, à clipser à la main pour obtenir une chaîne d'environ 190 mm. Chaque maillon a une rotule d'un côté et une douille à quatre pétales de l'autre. Les pétales plient au passage de la rotule puis se referment, ce qui laisse la chaîne se plier dans toutes les directions et se démonter sans outil. Chiffres utiles Largeur d'un maillon : 4,6 mm Pas entre maillons : 4,8 mm Longueur assemblée : environ 190 mm (40 maillons) Jeu théorique : 0,15 mm par côté, à ajuster selon l'imprimante Impression : maillons à plat, en deux colonnes de 20, sans supports Matériau conseillé : PETG, plus tolérant que le PLA pour les pétales fins Buse 0,4 mm, hauteur de couche 0,12 à 0,16 mm