50mm Rounded 4-Hole L-Bracket
Created 2 months ago
Description
A custom L-bracket with a fully radiused profile at the end of each arm. Built to support structural corners, shelves, or custom frames.
- Arm Dimensions: 50mm length, 20mm width
- Thickness: 4mm
- Mounting: Four 5mm holes total (two per leg), spaced for alignment and balanced load distribution.
- Profile: Radiused ends to prevent snagging and improve visual clearance.
Photos
Technical views
More like this
Explore more in Workshop & Tools →
Wide-Stance Filament Bracket Set
A sturdy, flat-packed filament spool holder with an open frame base and dual arching uprights. Designed for standard 16mm rods or dowels, this is laid out flat for maximum printing strength along the layer lines. Remix Hooks Rod Diameter: Currently tuned to 16.5mm to comfortably clear 16mm rods. Upright Spacing: The upright arches span 150mm between the 80mm and 60mm heights. Hardware: Sized for 9mm diameter screw heads to sink flush into the 10mm thick base, clamping down into the uprights.
Hilti Nuron Battery Bracket v3
What it's for A heavy-duty, wall-mounted slide bracket engineered specifically for Hilti Nuron battery packs. Designed to mount vertically, it features precision-cut clearance channels and flared 45-degree entry ramps for blind sliding, backed by a solid stop block to prevent bottoming out. Four reinforced, deep-countersunk screw channels ensure the mount stays locked to the wall regardless of the battery weight. Dimensions Overall footprint: 107 mm length × ~93 mm width × 23.5 mm depth. Internal track: 61.5 mm outer track width, 51.5 mm inner neck clearance. Mounting: 4× countersunk screw holes (5.5 mm shaft, 13.5 mm head, 5 mm deep sink). Print notes Recommend rigid, high-strength materials like PETG or ABS to handle the repeated friction and weight of the Nuron packs. Print face up with the flat back resting completely against the bed. Clearances are set to exact measurements, so a well-tuned printer is necessary to keep the slide rails from binding.
small Bottle Syringe Clip
A custom-sized double ring designed to couple a 14.5 mm syringe to a 31 mm bottle neck. Syringe bore: 14.5 mm with an 8 mm front insertion slot Bottle bore: 31 mm (snaps on via a 22 mm back slot) Clearance: 4 mm bridge spacing The branding is now recessed 0.6 mm directly into the bottle ring's inner wall, keeping the outer profile completely flush. Check your syringe outer barrel measurement before running this.
Biofloc Monitor Station Enclosure
An enclosure is only as good as the snarl of wires it prevents. This is a heavy-duty two-part monitor housing built specifically for FDM printing, designed to group, separate, and anchor a complete suite of biofloc water-quality electronics without turning into a bird's nest inside. The layout isolates the battery compartment at the bottom and keeps the DC buck converters and relay in a ventilated top section, leaving the central deck clear for the ESP32 and an array of sensor interfaces. Internal divider walls double as cable routing channels, forcing the wiring to stay orderly. Core Features Printability: Both halves print completely flat on the build plate (Z=0). The integrated bottom handle is flush with the front face to avoid overhangs. Dimensions: 170 mm width × 250 mm height × 75 mm depth. Hardware Required: 6× M3 screws for the rear cover; additional M3 hardware for the internal standoffs and the 16x2 LCD faceplate mount. Ports: Bottom panel holds 4× sensor ports (3× 8mm, 1× 6mm) with engraved labels. Right panel holds cutouts for 12V DC, an SD card slot, a rocker switch, and USB programming access.
Hilti Nuron Battery Mount
A wall-mounted receiver bracket for Hilti Nuron batteries. Heavy battery packs love to lever short brackets right out of the drywall. This bracket gives them a solid vertical footprint to spread that load, catching the battery's sliding interface on an internal U-channel with a dead stop at the base. Internal Channel: 63mm wide (48mm opening) Clearance: Counter-sunk screw holes keep the hardware below the sliding surface Detail: Features a debossed HILTI logo on the backplate that stays clear of the sliding path
28mm — Tapered Syringe Adapter
A specialized dual-ring tool designed to connect a small tapered syringe (5–6 mm) to a 28 mm bottle neck. Features Bottle Bore: 28 mm with a straight 8 mm snap-on cutout, finished with rounded entry tips. Syringe Bore: Tapered from 5 mm at the bottom to 6 mm at the top, ensuring a snug fit. Bridge: A short 6 mm tapered solid bridge connecting the two mounts smoothly. Branding: "SE Tool" engraved directly onto both side flanks of the tapered bridge.