8-Probe Slim Wall Rack
Created 1 months ago
Description
Tired of oscilloscope probes sliding off the bench and getting crushed by heavy gear? This wall-mounted rack gets them up and out of the way. It holds eight probes cleanly, keeping the cables untangled and the tips safe.
Dimensions & Details
- Capacity: 8 slots (15mm diameter cutouts, 5.5mm entry slots)
- Overall Size: 220mm wide x 53mm deep x 17.5mm high
- Mounting: Three countersunk screw holes (4.5mm shaft, 7.5mm head)
- Printing: Prints flat on its base, no supports required. Thinned down to save material and print time.
Images
More like this
Explore more in Workshop & Tools →
Biofloc Monitor Station Enclosure
An enclosure is only as good as the snarl of wires it prevents. This is a heavy-duty two-part monitor housing built specifically for FDM printing, designed to group, separate, and anchor a complete suite of biofloc water-quality electronics without turning into a bird's nest inside. The layout isolates the battery compartment at the bottom and keeps the DC buck converters and relay in a ventilated top section, leaving the central deck clear for the ESP32 and an array of sensor interfaces. Internal divider walls double as cable routing channels, forcing the wiring to stay orderly. Core Features Printability: Both halves print completely flat on the build plate (Z=0). The integrated bottom handle is flush with the front face to avoid overhangs. Dimensions: 170 mm width × 250 mm height × 75 mm depth. Hardware Required: 6× M3 screws for the rear cover; additional M3 hardware for the internal standoffs and the 16x2 LCD faceplate mount. Ports: Bottom panel holds 4× sensor ports (3× 8mm, 1× 6mm) with engraved labels. Right panel holds cutouts for 12V DC, an SD card slot, a rocker switch, and USB programming access.
60mm Winding Spool With Anchors
What it's for A compact, highly functional utility spool tailored for winding wires or thin cables. It features two specialized holes: a 2.5 mm pass-through hole at the base of the core to thread the start of the wire, and a smaller 1.5 mm hole on the outer edge of the flange to secure the loose end once wound. Dimensions Outer Diameter (Flanges): 60 mm Core Outer Diameter: 25 mm Central Axle Hole: 8 mm Groove Width (Winding Space): 15 mm Flange Thickness: 2.5 mm each (Total height: 20 mm) Assembly Slide onto an 8 mm rod or bolt to spin. Pass the start of the wire through the inner bottom hole to anchor it, wind evenly across the 15 mm groove, and lock the tail through the outer top hole.
4mm Square Key & Mount
The 4mm square key is the thing you can never find when a radiator needs bleeding or a panel needs opening. This gives the key a dedicated wall mount so it actually stays put. Includes a fitted bracket and custom printed M4 screws that use the same 4mm square drive as the key itself — meaning you don't even need a separate screwdriver to mount the bracket. Mounting bracket: 55mm × 15mm Key shaft: 4mm square Screw drive: 4.5mm square recess
2 cadenas module
A wall-mounted 200×200 mm lockout tagout station designed to hold 15 industrial safety padlocks. The single-piece board features reinforced, support-free pegs sized to slip through standard 6.35 mm padlock shackles, retaining them securely while lying completely flat on the print bed. Dimensions: 200 mm width × 200 mm height × 12 mm total depth Capacity: 15 padlocks (3 rows of 5) Hook Profile: 5 mm diameter shaft, expanding to a 7 mm chamfered retaining lip Material Guidelines: Optimized for PETG; standard print cooling recommended for the peg tips Mounting: Four 5 mm countersunk wall-mounting holes
Experimental Filter Housing V1
A multi-part FDM-optimized housing for testing granular and particulate filter media. Designed with discrete chambers, retaining grids, and standard O-ring sealing surfaces. Disclaimer: This is a strictly non-certified prototype for experimental projects. Do not use for certified respiratory protection. What it's for Testing layered filtration concepts. The housing accommodates a 26mm deep granular adsorption bed and an 8–10mm particulate filter section, separated by an air-distribution spacer. Media is retained by drop-in mesh grids, allowing rapid replacement during testing. Dimensions Overall Assembled Size: 80 mm diameter × 55 mm length Wall Thickness: 3 mm main shell Adsorption Chamber: 68 mm ID × 26 mm depth Connections: Rear standard 3-tab quarter-turn bayonet (35 mm OD tube) Print notes Orientation: Parts are laid out flat on the bed. The front cap should be flipped 180° in your slicer so its top face rests on the build plate. Supports: None required. The bayonet tabs are modeled with a 45° chamfer profile to print cleanly without support material. Tolerances: Threaded interfaces are built with 0.5–1mm diametrical clearances to accommodate standard PETG shrinkage.
Self-Centering V-Block Finder
A precision marking tool designed to locate the exact center of round and square stock. Eliminates the need to eyeball center lines when preparing material for drilling, turning, or joining. What it's for Self-Centering Base: A 90-degree V-groove securely seats the tool on both round dowels and square cuts. Tapered Pencil Slot: The marking slot tapers from 6mm down to a 1.5mm slit, physically forcing the pencil lead onto the true center line. Corner Relief: The apex of the V-groove includes a circular relief, preventing the sharp corners of square stock from binding. Dimensions Stock Compatibility: Accommodates material widths from 10mm up to 60mm. Overall Size: Measures roughly 86mm wide and 90mm long. Base Plate Thickness: The main plate is 4mm thick, providing a rigid straight edge. Remix ideas Extend the length of the plate and slot for marking deeper along the stock. Widen the V-arms to accommodate larger stock sizes like fence posts. Modify the slot taper to perfectly capture a specific mechanical pencil or marking knife.