8.5 Inch Tall Round Steamer Basket with Lid
Created today
Description
A round steamer basket, 216 mm (8.5 in) in outer diameter and 70 mm tall, with a separate conical lid. The floor is slotted for steam flow, and raised bands on the wall suggest bamboo.
- Basket: 216 mm OD, 70 mm tall, 5 mm floor, 5 mm wall
- Floor: radial steam slots in three rings
- Lid: conical, with a round knob, fits over the rim
- Bands: three raised rings, surface detail only
- Print: two separate pieces, lid printed flat side down
Images
More like this
Explore more in Kitchen & Bathroom →
lid 2
A round plug-style lid for a container with a roughly 94 mm inside diameter. A 100 mm flange rests on the rim and an 8 mm deep, 93.4 mm plug drops into the bore. Fitment Fits: round containers with a bore near 94 mm. Does not fit: bores under 93.4 mm, or slip-over use on a rim. Measure before printing: the container's inside diameter. The plug is 93.4 mm, so a 94 mm bore leaves 0.3 mm per side. Details: the underside is hollowed to 87 mm, leaving a 3 mm flange top and a 3.2 mm plug wall. Overall height: 11 mm.
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use
36mm Bore Honeycomb Egg Dispenser
An upright, gravity-fed egg dispenser scaled for a 36mm bore, fitting quail or small pullet eggs. The Fitment: 36mm internal width. This will immediately jam on standard grocery store Grade A Large eggs. The Structure: Uses a 1.8mm solid-web honeycomb shell to reduce material use without sacrificing structural rigidity or leaving isolated printing islands. The Feed: Features an internal 18mm high sloped ramp leading down to an arched dispensing port.
Galaxy Cap & Pets
A standalone pop-top can cover designed for easy swapping of customizable 3D-printable pets. Hooks for Remixing The Peg System: The mounting peg on the cap is a standard 3.8 mm cylinder, sitting slightly toward the back edge. Any custom object with a matching 4.2 mm socket will drop right on. Skull Profile: The flat skull on the cap is an exact scaled-down copy of the original 3D geometry. Expansion: Want to add more utility? You could stretch the cap base horizontally to house three or four pets simultaneously, or angle the peg so the figure faces upward when the can is open.
Components view 1st
A touchless smart tap automation enclosure designed to sit directly onto a 15–24 mm tap throat. This is the fully assembled internal view of the water and power management systems. The IP65-style base box drops over the E18-D80NK IR proximity sensor up front and houses native standoffs for standard 50×40 mm and 35×25 mm logic boards. Fitment Checklist Throat: Clamps over 15–24 mm circular taps Sensor Bore: Front-facing 18 mm drop-in for cylindrical IR sensors Tubing: Routing pathways built strictly for 6 mm OD / 4 mm ID polyurethane lines Valve Clearance: Central bay fits standard inline 1/4" 12V DC solenoids